Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 447

background image

2.30

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

PVT / FINAL DRIVE / WHEEL AND TIRE

DRIVE CLUTCH / DRIVEN CLUTCH / BELT
SERVICE

Refer to Chapter 6 “Clutching (PVT)” for service and
removal procedures.

PVT INTAKE PRE-FILTER SERVICE

It is recommended that the PVT intake pre-filter be
inspected daily. The filter should be inspected using the
following procedure:

1.

The PVT intake pre-filter (A) is located just behind
the passenger hip bolster on the right side of the
vehicle.

2.

Press in (towards the front of the unit) on intake pre-
filter tab (B) to remove it.

3.

Inspect the pre-filter. If necessary, clean with soapy
water and dry with low pressure compressed air.

PVT DRYING

NOTE

After operating in water, the vehicle’s PVT system

should be checked immediately. Use the following

instructions to dry it out before operating.

The PVT drain plug (C) is located at the bottom of the
outer clutch cover. Access the drain plug through the left
rear wheel well.

1.

Using a flat blade screwdriver, remove the PVT drain
plug (C) and O-ring from the outer clutch cover.

2.

Allow the water to drain out completely.

3.

Reinstall the drain plug and O-ring.

4.

Place the transmission in PARK, apply the brake and
start the engine.

5.

Apply varying throttle for 10-15 seconds to expel the
moisture and air-dry the belt and clutches.

NOTE

Do not hold the throttle pedal wide open for more than 5

seconds.

6.

Allow the engine RPM to return to idle, then shift the
transmission into low gear.

7.

Test the PVT system for belt slippage. If the belt
slips, repeat the process or remove the outer clutch
cover to inspect the PVT system (see Chapter 6
“Clutching

(PVT)”

for

service

and

removal

procedures).

NOTE

If the vehicle has ingested a large amount of water into

the PVT system and has not been operated for a period

of time, be sure to check the PVT system components

for water damage.

«
...
45
46
47
48
49
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: MANCO Страницы: 8

Бренд: XY Powersports Страницы: 259

RYKER 2023 Series

Бренд: Can-Am Страницы: 222

Maverick Sport 1000 2021

Бренд: Can-Am Страницы: 195

Бренд: Fisher-Price Страницы: 40

150GKA-2 Series

Бренд: Kandi USA Страницы: 16

FourTrax Foreman TRX520FE2 2020

Бренд: Honda Страницы: 287

Бренд: Yamaha Страницы: 60

Grizzly YFM125GW

Бренд: Yamaha Страницы: 146

Бренд: Hammerhead Страницы: 55

Бренд: Power Fist Страницы: 8

Бренд: Honda Страницы: 65

Cushman HAULER 800X ELiTE 2019

Бренд: Textron Specialized Vehicles Страницы: 66

Sportsman XP Touring 1000

Бренд: Polaris Страницы: 121

Бренд: Polaris Страницы: 131

Sportsman Forest 500

Бренд: Polaris Страницы: 138

Sportsman 9922581

Бренд: Polaris Страницы: 137

Sportsman X2 850

Бренд: Polaris Страницы: 158

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды