Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 318 | Manualshive

Страница: 318 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

7.31

11. Slide the small boot clamp and boot (small end first)

onto the drive shaft and position the boot in its
groove machined in the shaft.

12. Install a NEW circlip on the end of the shaft.

13. Grease the joint with the special CV joint grease

provided in the boot replacement kit. Fill the cavity
behind the balls and the splined hole in the joint’s
inner race. Pack the ball tracks and outer face flush
with grease. Place any remaining grease into the
boot.

CAUTION

The grease provided in the replacement kit is specially
formulated for wear resistance and durability. DO NOT

use substitutes or mix with other lubricants.

NOTE

It is very important to use the correct type and quantity

of grease by using all the grease included with the boot

kit. DO NOT use a substitute grease and DO NOT

overfill or under fill the CV joint.

14. Fully compress the joint and push the drive shaft

firmly into the inner race.

15. Align the circlip with the lead-in chamfer.

16. Use a soft-faced hammer to tap the joint onto the

drive shaft until you reach the end of the splines and
the joint locks in place.

17. Pull on the joint to test that the circlip is seated and

that the joint is securely fastened to the shaft.

18. Remove excess grease from plunging joint’s external

surfaces and place the excess grease in the boot.

19. Pull the boot over the joint and position the boot lips

into the grooves on the joint housing and shaft. Make
sure the boot is not dimpled or collapsed.

20. Install and tighten the small clamp using the

appropriate clamp tool.

Axle Boot Clamp Tool: PU-48951orCV Boot Clamp

Pliers: 8700226

21. Pull out on drive shaft to center joint in the housing.

Slide a straight O-ring pick or a small slotted screw
driver between the large end of the boot and the joint
housing and lift up to equalize air pressure in the
boot.

22. Position the boot lip in its groove. Install and tighten

the large clamp using the appropriate clamp tool.

Axle Boot Clamp Tool: PU-48951orCV Boot Clamp

Pliers: 8700226

«
...
316
317
318
319
320
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

120 Sno Pro 2010

Бренд: Arctic Cat Страницы: 562

Бренд: Komatsu Страницы: 435

Бренд: Seizmik Страницы: 10

Бренд: Access Страницы: 72

Бренд: MINIMOTO Страницы: 33

Бренд: Strongway Страницы: 3

Бренд: Kazuma Страницы: 36

UTV 2x4 Series 11

Бренд: Polaris Страницы: 108

ESCALATE TRAILER ET 12000

Бренд: Bil-Jax Страницы: 20

Бренд: Landoll Страницы: 88

Бренд: Gatekeeper Systems Страницы: 60

Бренд: Yamaha Страницы: 293

Бренд: Access Motor Страницы: 65

Бренд: Polaris Страницы: 231

Бренд: BERG Страницы: 8

FTK 4000 Series

Бренд: Humbaur Страницы: 20

Бренд: Yamaha Страницы: 841

Бренд: Thump Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды