Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 348 | Manualshive

Страница: 348 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

8.29

26. Inspect the shift drum for any damage or wear.

Inspect the splines of the shift drum.

27. Install the shift drum (E) into the transmission

housing. Lift up on the shift shaft rail (D) and move
the rail assembly towards the shift drum to allow the
shift fork ends to be installed into the shift drum (E).

28. Apply a continuous bead of Crankcase 3 Bond

Sealant (PN 2871557) to the left hand transmission
mating surface.

29. Install the transmission case cover and retaining

bolts. Torque bolts to specification.

TORQUE

Transmission Case Bolts:

15-20 ft-lbs (20-27 Nm)

30. Install new seals into the transmission case halves.

• The snorkel shaft seal (F), should be pressed in until it

seats against the housing counter-bore.

• The input shaft seal (G), should be pressed in until it

seats flush with the housing.

• The rear output shaft seals (H), can be installed using

a standard bushing installation tool. Seals should be
installed just past the case lead-in chamfer (.070" or
1.8 mm from outer face of bore).

«
...
346
347
348
349
350
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: Jianshe Страницы: 82

Бренд: Airstream Страницы: 98

Бренд: Land Pride Страницы: 132

650 MUD PRO 2011

Бренд: Arctic Cat Страницы: 84

Бренд: Blaw-Knox Страницы: 118

Бренд: NorAM Страницы: 613

Бренд: GSMOON Страницы: 49

Бренд: E-Z-GO Страницы: 192

Бренд: Taylor-Dunn Страницы: 232

EVINRUDE Johnson 5007118

Бренд: BRP Страницы: 14

KODIAK 700 2018

Бренд: Yamaha Страницы: 180

Бренд: Yamaha Страницы: 150

GRIZZLY 350 YFM35FGD

Бренд: Yamaha Страницы: 144

Бренд: KAYO MOTO Страницы: 8

Бренд: Toro Страницы: 24

Бренд: Toro Страницы: 64

Бренд: Standart Motor Corp Страницы: 108

Бренд: ROSSO MOTORS Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды