Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 366

Страница: 366 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

9.13

FRONT BRAKE PADS

PAD REMOVAL

Elevate and support front of vehicle.

CAUTION

Use care when supporting vehicle so that it does not tip

or fall.Severe injury may occur if machine tips or falls.

Remove the wheel nuts, washers and front wheel.
Loosen pad adjuster screw.

Remove the upper and lower caliper mounting bolts
and remove the caliper from the front hub.

NOTE

When removing caliper, use care not to damage brake

line. Support caliper to avoid kinking or bending brake

line.

Push caliper piston into caliper bore slowly using a
C-clamp or locking pliers with pads installed.

NOTE

Brake fluid will be forced through compensating port

into master cylinder fluid reservoir when piston is

pushed back into caliper. Remove excess fluid from

reservoir as required.

Push the mounting bracket inward and slip outer
brake pad out between the bracket and caliper body.

Remove the inner pad from the bracket and caliper.

BRAKES

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды