Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 447

background image

3.16

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

ENGINE COOLING SYSTEM

Cooling System Specifications

CONDITION

COOLANT TEMPERATURE °
F (°C)

Room Temperature

68° F (20° C)

Thermostat Open

180° F (82° C)

Fan Off

194° F (90° C)

Fan On

205° F (96° C)

Thermostat
Full Open Lift

203° F (95° C)

Engine Temperature
Overheat Indicator

232° F (111° C)

Engine Protection
Level 1 - Power Limit

232° F (111° C)

Engine Protection
Ignition Misfire

237° F (114° C)

Engine Protection
Level 2 - Power Limit

244° F (118° C)

Engine Protection
Shutdown

252° F (122° C)

ITEM

SPECIFICATION

Cooling System Capacity

5 qts. (4.7 L)

Pressure Cap Relief

13 PSI

Polaris Premium Antifreeze2871534 - Quart2871323 -

Gallon

Recommended Coolant

Use only high quality antifreeze/coolant mixed with
distilled water in a 50/50 or 60/40 ratio, depending on
freeze protection required in your area.

CAUTION:

Using tap water in the cooling system will

lead to a buildup of deposits which may restrict coolant
flow and reduce heat dissipation, resulting in possible
engine damage. Polaris Premium 60/40 Antifreeze/
Coolant is recommended for use in all cooling systems
and comes pre-mixed, ready to use.

COOLING SYSTEM PRESSURE TEST

1.

Remove the hood from the front cab.

WARNING

Escaping steam can cause burns. Never remove the

pressure cap while the engine is warm or hot. Always

allow the engine to cool before removing the pressure

cap.

2.

Remove the pressure cap from the radiator and
pressure

test

the

cooling

system

using

a

commercially available tester.

3.

The system must maintain 10 psi for five minutes or
longer. If pressure loss is evident within five minutes,
check the radiator, all cooling system hoses, clamps
and water pump seal for leakage.

RADIATOR CAP PRESSURE TEST

1.

Open the front hood (see Warning under “Cooling
System Pressure Test”).

2.

Remove radiator pressure cap and test using a
pressure cap tester (commercially available).

3.

The radiator cap relief pressure is 13 psi. Replace
cap if it does not meet this specification.

«
...
71
72
73
74
75
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Street Rider 150MRX

Бренд: Texas Страницы: 33

Бренд: Texas Страницы: 49

Sportsman 850 2021

Бренд: Polaris Страницы: 180

Sportsman 800 Big Boss

Бренд: Polaris Страницы: 143

Бренд: KAYO MOTOR Страницы: 91

Stand-Up SINGLE RIDE-UP Go Series

Бренд: Kendon Страницы: 20

Бренд: Yamaha Страницы: 52

Бренд: URBANGLIDE Страницы: 16

Бренд: Sym Страницы: 100

Quad Lander 300

Бренд: Sym Страницы: 244

Бренд: PIAGGIO Страницы: 160

Бренд: Kubota Страницы: 75

Бренд: Kubota Страницы: 91

Бренд: Kubota Страницы: 96

Бренд: Kubota Страницы: 379

Бренд: Ironhorse Trailers Страницы: 13

Бренд: Atlas Copco Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды