Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 371

Страница: 371 / 447

9.18

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

Once the pistons are removed, use a pick to carefully
remove the square O-rings from the caliper. O-rings
should be replaced during caliper service.

Clean the caliper body, piston, and retaining bracket
with brake cleaner or alcohol.

NOTE

Be sure to clean the seal grooves in caliper body.

CALIPER INSPECTION

Inspect caliper body for nicks, scratches, pitting or
wear.

Measure

bore

size

and

compare

specifications. Replace if damaged or worn beyond
service limit.

MEASUREMENT

Front Caliper Piston Bore I.D.:

Standard: 1.373” (34.87

mm)Service Limit: 1.375” (34.93 mm)

Inspect piston for nicks, scratches, pitting or wear.
Measure piston diameter and replace if damaged or
worn beyond service limit.

MEASUREMENT

Front Caliper Piston O.D.:

Standard: 1.370” (34.80

mm)Service Limit: 1.368” (34.75 mm)

Inspect brake disc and pads as outlined in this
chapter.

BRAKES

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды