Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 388 | Manualshive

Страница: 388 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

10.3

GENERAL INFORMATION

SPECIAL TOOLS

PART
NUMBER

TOOL DESCRIPTION

PV-43568

Fluke™ 77 Digital Multimeter

PV-43526

Connector Test Kit

2870630

Timing Light

2460761

Hall Effect Sensor Probe Harness

2871745

Static Timing Light Harness

PU-50296

Battery Conductance Analyzer
(MDX-610P)

PU-49466

Relay Bypass

-

Digital Wrench® (see Chapter 4)

Bosch Automotive Service Solutions

:

1-800-345-2233 or http://polaris.service-solutions.com/

ELECTRICAL SERVICE NOTES

Keep the following notes in mind when diagnosing an
electrical problem:

• Refer to wiring diagram for stator and electrical

component resistance specifications.

• When measuring resistance of a component that has a

resistance value under 10 Ohms, remember to
subtract meter lead resistance from the reading.
Connect the leads together and record the resistance.
The resistance of the component is equal to tested
value minus the lead resistance.

• Become familiar with the operation of your meter. Be

sure leads are in the proper jack for the test being
performed (i.e. 10A jack for current readings). Refer to
the Owner’s Manual included with your meter for more
information.

• Voltage, amperage, and resistance values included in

this manual are obtained with a Fluke™ 77 Digital
Multimeter (PV-43568). This meter is used when
diagnosing electrical problems. Readings obtained
with other meters may differ.

• Pay attention to the prefix on the multimeter reading

(K, M, etc.) and the position of the decimal point.

• For resistance readings, isolate the component to be

tested. Disconnect it from the wiring harness or power
supply.

COMPONENTS UNDER HOOD

The following components can be accessed under the
hood.

• Voltage Regulator (in front of radiator)
• Terminal Block

• Headlight Connectors

COMPONENTS BEHIND DASH PANEL

The following components can be accessed with the
upper dash panel removed.

• Instrument Cluster (Speedometer)
• AWD/2WD/TURF Switch
• Headlight Switch
• 12 VDC Accessory Power Points
• Ignition Key Switch

COMPONENTS UNDER PASSENGER SEAT
BASE

The following components can be accessed with the
passenger seat base removed.

• Battery*
• Battery Cables*
• Starter Solenoid*
• Relays*
• Fuses*
• Digital Wrench ® Diagnostic Connector*
• ECU*
• Speed Key Accessory (if installed)

NOTE

*Components are located under rear passenger seat

base on 2014 RANGER CREW 900

«
...
386
387
388
389
390
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: Baja motorsports Страницы: 15

Бренд: Baja motorsports Страницы: 50

Бренд: Honda Страницы: 29

Бренд: Taylor-Dunn Страницы: 166

Бренд: Bosch Страницы: 2

Бренд: Suzuki Страницы: 54

Trailblazer E2020

Бренд: Evinrude Страницы: 14

65 TREE Transplanter

Бренд: Dakota Страницы: 16

Tugger train Autarkic E Frame

Бренд: Still Страницы: 144

Бренд: Texas Страницы: 7

Falcon Go-kart 2018

Бренд: J&J Amusements Страницы: 58

Бренд: Realtree Страницы: 12

Бренд: Labrie Страницы: 62

Бренд: Moni Страницы: 16

Бренд: Landoll Страницы: 72

Бренд: KAYO MOTOR Страницы: 91

Бренд: Taxa Outdoors Страницы: 5

MARGAY racing K3

Бренд: Ignite Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды