Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 172 | Manualshive

Страница: 172 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

4.23

ELECTRONIC THROTTLE CONTROL (ETC)

OPERATION OVERVIEW

NOTE

DO NOT attempt to service the ETC. The ETC is a non-

serviceable component and can only be tested using

Digital Wrench®. If the ETC is faulty, the entire

assembly must be replaced.

Mounted to the intake plenum, the ETC acts as an
electronically controlled throttle body. The ETC controls
engine throttle operation to provide the proper air/fuel
ratio needed for engine operation at all RPM ranges. The
ETC controls engine RPM based off input provided by
the Pedal Position Sensor (PPS) and Electronic Control
Unit (ECU).

ETC TEST

Never attempt to disassemble the ETC assembly.
Warranty is void if the end cover is opened or tampered
with in any way.

All operating and control functions within the ETC are
pre-set. No internal servicing or adjustments may be
performed. If a problem is encountered, and you
determine the ETC to be faulty, contact the Polaris
Service Department for specific handling instructions. Do
not replace the ETC without factory authorization.
Use Digital Wrench® to perform all troubleshooting of
this component. Use a Volt Ohm meter to test the vehicle
harness continuity between the ETC connector and ECU
connector. Refer to the wire diagram for pin-out details. If
the ETC is faulty, the entire ETC assembly must be
replaced (see "ETC Replacement").

ETC REPLACEMENT

1.

Lift the rear cargo box to the raised position.

2.

Remove wire harness from ETC retainer clip (A) and
remove the ETC connector (B).

3.

Loosen the clamp (C) retaining the intake boot to the
ETC. Remove the boot from the ETC.

4.

Remove the (4) bolts (D) retaining the ETC housing
to intake plenum.

5.

Remove the ETC housing and gasket (E) from intake
plenum.

6.

Reverse these steps for installation. Torque the ETC
housing retaining bolts and intake boot clamp to
specification.

TORQUE

ETC Housing Retaining Bolts:

7 ft-lbs (10 Nm)

Intake

Boot Clamp:

35 in-lbs (4 Nm)

FUEL SYSTEM - GENERAL

«
...
170
171
172
173
174
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: Ace Sports Страницы: 79

Бренд: AC Air Technology Страницы: 49

Бренд: Taylor-Dunn Страницы: 166

Бренд: Yamaha Страницы: 21

Vyper 4WD 1100cc 4 seater XY1100UEL

Бренд: gio Страницы: 261

Бренд: KMW Страницы: 98

Бренд: Labrie Страницы: 62

Бренд: Yamaha Страницы: 42

Бренд: Baja motorsports Страницы: 77

K2 QUAD 250 - SERVICE

Бренд: GAS GAS Страницы: 64

BurdenMaster B 2-00

Бренд: Taylor-Dunn Страницы: 266

GRIZZLY 700 2013

Бренд: Yamaha Страницы: 174

Бренд: Yamaha Страницы: 32

Бренд: Yamaha Страницы: 162

Бренд: E-TON Страницы: 225

Бренд: Arctic Cat Страницы: 92

Dump Series D5TLP

Бренд: Anderson Manufacturing Страницы: 1

Trail-Blazer TB-6000

Бренд: J&M Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды