Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 33

Страница: 33 / 447

2.16

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

AIR FILTER SERVICE

Inspect the air filter at the intervals outlined in the
Periodic

Maintenance

Chart.

extremely

dusty

conditions, air filter replacement will be required more
often.

Tilt the rear cargo box to access the airbox.

Release the (5) airbox cover latches (C) and lower
the bottom cover (D) to access the air filter element.

Remove the air filter element (E).

NOTE

Leave the front portion of the lower airbox cover in the

hinges. It is not necessary to remove the lower cover

when servicing the air filter.

Inspect the airbox for oil or water deposits. Wipe
away any deposits with a clean shop towel.

NOTE

If the filter has been soaked with fuel or oil it must be

replaced.

Inspect the air filter and replace if necessary.

NOTE

DO NOT attempt to clean the air filter.

Place the air filter into the airbox. Reposition the
lower airbox cover and install the (5) retaining
latches.

MAINTENANCE

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды