Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 324 | Manualshive

Страница: 324 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

8.5

SHIFT CABLE

INSPECTION

Shift cable adjustment may be necessary if symptoms
include:

• No gear position or AWD display on instrument cluster
• Ratcheting noise on deceleration
• Inability to engage into a gear
• Excessive gear lash (noise)
• Gear selector moving out of desired range

Inspect shift cable, clevis pins, and pivot bushings and
replace if worn or damaged.

ADJUSTMENT

1.

Locate the shift cable (A) attached to the mount
bracket (B) and transmission in the right rear wheel
well area.

2.

Inspect shift cable (A), dust boot (C) and the clevis
pin and pivot bushings (D). Replace if worn or
damaged.

3.

If adjustment is required, loosen the lower jam nut
(E) and pull the cable out of the mount bracket to
move the upper jam nut (F).

4.

Adjust the shift cable so there is the same amount of
cable travel when shifting slightly past HIGH gear
and PARK.

5.

Thread the upper or lower jam nut as required to
obtain proper cable adjustment.

NOTE

This procedure may require a few attempts to obtain

the proper adjustment.

6.

Once the proper adjustment is obtained, place the
shift cable and upper jam nut into the mount. Tighten
the lower jam nut (E) against the mount.

7.

Start engine and shift through all gears to ensure the
shift cable is properly adjusted. If transmission still
ratchets after cable adjustment, the transmission will
require service.

«
...
322
323
324
325
326
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Cyclone IV Trekking

Бренд: Radical Design Страницы: 2

Бренд: E-TON Страницы: 36

Sportsman 800 EFI

Бренд: Polaris Страницы: 388

Бренд: E-TON Страницы: 38

Бренд: Qlink Страницы: 168

Бренд: Can-Am Страницы: 423

Бренд: Coleman Powersports Страницы: 38

Бренд: Yamaha Страницы: 87

WOLVERINE YFM45FXX

Бренд: Yamaha Страницы: 166

VIKING YXM70VPXG

Бренд: Yamaha Страницы: 172

2009 LT-A750XK9

Бренд: Suzuki Страницы: 711

CUSHMAN ELECTRIC TUG E-Z-GO XI 340

Бренд: Textron Страницы: 50

Scrambler 400 4X4

Бренд: Polaris Страницы: 2

RANGER RZR 2008

Бренд: Polaris Страницы: 20

Scrambler 500 4x4

Бренд: Polaris Страницы: 129

Sportsman 570 EFI

Бренд: Polaris Страницы: 148

RZR XP 1000 EPS High Lifter Edition

Бренд: Polaris Страницы: 152

SNOWMOBILE 2001

Бренд: Polaris Страницы: 169

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды