Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 130

Страница: 130 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

3.73

21. Apply a thin, continuous film of Crankcase Sealant

(PN 2871557)

to sump cover mating surface

. Do

not allow sealant to dry before assembly.

NOTE

Dipstick must be removed before oil pan is assembled

to the engine. Failure to do this will damage the

dipstick.

22. Install the oil sump cover

onto the crankcase.

23. Install the thirteen M6

and three M8 bolts that

retain the oil sump cover

to the crankcase.

24. Torque the oil sump cover bolts in sequence to

specification. Repeat the sequence to verify final
torque.

TORQUE

Oil Sump Cover Bolts:

M6 Bolts:

9 ft-lb (12 Nm)

M8 Bolts:

26 ft-lb (35 Nm)

25. Reinstall the crankcase drain plug if previously

removed. Torque drain plug to specification.

TORQUE

Crankcase Drain Plug:

11 ft-lbs (15 Nm)

26. Rotate the engine so the cylinder is facing up.

27. Reinstall the oil cooler

, if previously removed. Use

new O-rings

upon installation

ENGINE

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды