Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 416 | Manualshive

Страница: 416 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

10.31

REGULATOR / RECTIFIER

1.

Note: The regulator / rectifier is located in front of the
radiator. Remove the hood.

2.

Disconnect the wire harness from both headlights.

3.

Remove the (4) T40 Torx screws and (8) push rivets
retaining the front fascia (see Chapter 5).

4.

Carefully remove the front fascia assembly from the
vehicle to access the regulator / rectifier (A).

5.

If replacing the regulator / rectifier, remove the (2)
retaining screws (B) and disconnect the wire harness
(C). Remove the regulator (A) and heat sink plate (D)
from the vehicle.

6.

Reverse this procedure to install the new regulator /
rectifier and heat sink plate.

NOTE

If the regulator / rectifier case temperature exceeds

230° F or 110° C, the unit will turn itself off to cool down.

The unit will turn on again after it has cooled down to at

least 212° F or 100° C. If it turns off, verify the cooling

fins are clean, free from debris and that adequate

airflow is present.

«
...
414
415
416
417
418
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: Massimo Motor Страницы: 165

1993 TRX300FW Fourtrax 300 4x4

Бренд: Honda Страницы: 157

Бренд: J&J Amusements Страницы: 272

Camoplast ATV T4S

Бренд: CAMSO Страницы: 16

5000-05-1774-MAN

Бренд: CAMSO Страницы: 17

Бренд: PRONAR Страницы: 83

Бренд: E-TON Страницы: 38

Бренд: Landoll Страницы: 80

Бренд: Malone Страницы: 4

Grizzly 450 YFM45FGPD

Бренд: Yamaha Страницы: 172

Бренд: Access Motor Страницы: 65

SmarTrax John Deere 8X60 Series

Бренд: Raven Страницы: 48

Бренд: Honda Страницы: 65

Бренд: Treker Страницы: 56

Бренд: Sauber Страницы: 11

Бренд: Primo Water Страницы: 12

Бренд: Primo Water Страницы: 12

LittleGiant Trailer TLK864

Бренд: Lets Go Aero Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды