Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 326

Страница: 326 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

8.7

10. Disconnect the transmission shift cable (L) by

removing the clip (M) and sliding the washer and
shift cable off the bellcrank.

11. Mark the location of the upper shift cable jam nut (N).

Loosen the lower jam nut (P) and remove the shift
cable assembly from the bracket (Q).

12. Relieve pressure from the fuel rail. Disconnect the

fuel line at the fuel rail wrap the ends with a clean rag
to assure no dirt gets in the fuel system.

13. Using a 13mm socket and wrench, remove the

fastener (R) securing the bottom of the intake
plenum to the rear transmission mount.

14. Using a long screwdriver, loosen both hose clamps

(S) that retain the intake plenum runners to the
cylinder head intake adapters. Remove the intake
plenum

and

electronic

throttle

control

assembly.

TRANSMISSION

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды