Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 76

Страница: 76 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

3.19

Remove the thermostat cover (B), seal (D) and
thermostat (E) from the engine.

NOTE

Thermostat has a pop-off relief to allow the bypass

system to operate until thermostat opens.

Clean thermostat mating surfaces on the engine and
thermostat cover.

Install a new thermostat and seal into the cover and
install the cover onto engine.

10. Install the thermostat cover bolts and torque the bolts

to specification.

TORQUE

Thermostat Cover Bolts:89 ± 9 in-lbs (10 ± 1 Nm)

11. Install coolant hose back on the thermostat cover

and securely tighten the hose clamp.

12. Fill cooling system and proceed to “Cooling System

Bleeding Procedure” provided in this chapter.

ENGINE

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды