Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

2.33

ELECTRICAL AND IGNITION SYSTEM

BATTERY MAINTENANCE

Keep

battery

terminals

and

connections

free

of

corrosion. If cleaning is necessary, remove the corrosion
with a stiff wire brush. Wash with a solution of one
tablespoon baking soda and one cup water. Rinse well
with tap water and dry off with clean shop towels. Coat
the terminals with dielectric grease or petroleum jelly.

WARNING

CALIFORNIA PROPOSITION 65 WARNING:

Batteries,

battery posts, terminals and related accessories contain

lead and lead compounds, and other chemicals known

to the State of California to cause cancer and birth

defects or other reproductive harm.WASH HANDS

AFTER HANDLING.

WARNING

Battery electrolyte is poisonous. It contains sulfuric

acid. Serious burns can result from contact with skin,

eyes or clothing. Antidote:

External:

Flush with water.

Internal:

Drink large quantities of water or milk. Follow

with milk of magnesia, beaten egg, or vegetable oil. Call

physician immediately.

Eyes:

Flush with water for 15 minutes and get prompt

medical attention.

Batteries produce explosive gases. Keep sparks, flame,

cigarettes, etc. away. Ventilate when charging or using

in an enclosed space. Always shield eyes when

working near batteries. KEEP OUT OF REACH OF

CHILDREN.

NOTE

Batteries must be fully charged before use or battery

life will be reduced by 10-30% of full potential. Charge

battery according to “Charging Procedure” provided in

Chapter 10. Do not use the vehicle’s stator/alternator to

charge a new battery.

BATTERY CHARGING / OFF SEASON
STORAGE

Refer to Chapter 10 “Electrical” for charging and off
season storage procedures.

BATTERY REMOVAL

1.

Remove the passenger seat (right rear passenger
seat on the CREW 900) and storage container to
access the battery (A).

2.

Disconnect the black (negative) battery cable (B).

3.

Disconnect the red (positive) battery cable (C).

CAUTION

To reduce the chance of sparks, disconnect the black

(negative) cable first. When reinstalling the battery,

connect the black (negative) cable last.

4.

Remove the fastener (D) retaining the battery hold-
down strap and lift the battery out of the vehicle.

BATTERY INSTALLATION

NOTE

Using a new battery that has not been fully charged can

damage the battery and result in a shorter life. It can

also hinder vehicle performance. Follow the battery

charging procedure in Chapter 10 “Electrical” before

installing the battery.

1.

Ensure the battery is fully charged.

2.

Place the battery (A) in the vehicle. Install the hold-
down strap and retaining fastener (D).

3.

Coat

the

terminals

with

dielectric

grease

or

petroleum jelly.

«
...
48
49
50
51
52
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

WOLVERINE YFM45FXV

Бренд: Yamaha Страницы: 34

BLASTER YFS200S

Бренд: Yamaha Страницы: 46

2005 Ranger 4x4

Бренд: Polaris Страницы: 121

Бренд: citEcar Страницы: 28

TRX250EX Sportrax250EX

Бренд: Honda Страницы: 203

Бренд: Cushman Страницы: 158

Бренд: Oldenbourg group Страницы: 60

RANGER XP 1000 2020

Бренд: Polaris Страницы: 156

2008 Outlander 400 EFI

Бренд: Can-Am Страницы: 599

Бренд: Egholm Страницы: 12

Sportsman 800 EFI 4x4 2012

Бренд: Polaris Страницы: 485

Бренд: QERIDOO Страницы: 36

Outlander Series 500

Бренд: Can-Am Страницы: 504

Бренд: Yamaha Страницы: 150

All Terrain Vehicle 250

Бренд: CROSSRUNNER Страницы: 16

Бренд: Sauber Страницы: 11

Бренд: Eagle Страницы: 24

Бренд: Kolpin Outdoors Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды