Omron NJ501-4300 Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 336

background image

4 Robot Instructions

4 - 42

NJ-series NJ Robotics CPU Unit User’s Manual (W539)

• The robot (axes group) moves from the current position and tracks the workpiece specified in

Init-

WrokpiecePosition

(Initial Workpiece Position).

• When the robot catches up the workpiece, the

InSync

(In Sync) output variable changes to TRUE.

After this, synchronization is maintained.

• To cancel synchronization, use the MC_SyncOut (End Synchronization) instruction in normal opera-

tion.

• When defining and selecting UCS for MC_SyncLinearConveyor, Z Axis must be parallel to the MCS

Z Axis because the conveyor tracking is only performed in X, Y and not in Z.

• The workspace check is performed if it is enabled. If an error is detected, the axes group operation

stops.
Refer to

2-3-2 Workspace Check

on page 2-23 for details on the workspace.

• While the command position is created, the command velocity and command acceleration rate that

are adjusted for the conveyor velocity are also created. The instruction checks whether or not these
values exceed

MaxVelocity

(Velocity Error Detection Value) or

MaxAcceleration

(Acceleration Error

Detection Value). If a specified limit is exceeded, an error occurs and the axis stops.

• Checks for

MaxVelocity

(Velocity Error Detection Value) and

MaxAcceleration

(Acceleration Error

Detection Value) at instruction execution is performed for a trajectory for the workpiece which is not
moved. For this reason, a velocity error or an acceleration error may be detected in position ranges
after Phase2, depending on the conveyor velocity.

• If a Motion Control Period Exceeded error occurs, it may cause a velocity error or an acceleration

error. Create the program and make the setting so that they do not cause a Motion Control Period
Exceeded error.

• You can use this instruction only when all the following conditions are met.

a) The kinematics is already set with MC_SetKinTransform (Set Kinematics Transformation)

instruction.

b) Home for all axes registered in the axes group are already defined.
c) The Servo is already ON for all axes registered in the axes group.
d) The limit input is OFF for all axes registered in the axes group.
e) The axes group is enabled.

In-Out Variables

Name

Meaning

Data type

Valid

range

Description

AxesGroup

Axes Group

_sGROUP_REF

---

Specify the axes group.

ConveyorAxis

Conveyor Axis

_sAxis_REF

---

Specify the axis.

Function

«
...
144
145
146
147
148
...
»

Содержание NJ501-4300

















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NJ501-4300

615 Series ANSI

Бренд: ABB Страницы: 60

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: QUAD Страницы: 16

Бренд: BADLANDS Страницы: 2

Бренд: Campbell Страницы: 3

Бренд: Eaton Страницы: 100

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Faro Barcelona Страницы: 8

Бренд: Faro Страницы: 3

Бренд: YASKAWA Страницы: 456

Бренд: York Страницы: 20

Бренд: YASKAWA Страницы: 49

Бренд: M-system Страницы: 17

Бренд: Madison AV Страницы: 2

Centronic SunWindControl SWC245-II

Бренд: Becker Страницы: 52

Бренд: Elotech Страницы: 20

Бренд: Intermatic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды