NEC V850E/Dx3 Скачать руководство пользователя страница 323 | Manualshive

Страница: 323 / 930

background image

323

DMA Controller (DMAC)

Chapter 8

Preliminary User’s Manual U17566EE1V2UM00

Set DMACTn according to the following table:

8.4 Automatic Restart Function

The DMA source address registers (DSAHn, DSALn), DMA destination
address registers (DDAHn, DDALn), and DMA transfer count register (DBCn)
are buffer registers with a 2-stage FIFO structure, named master and slave
register.

The setup data of the slave registers is always used for the current DMA
transfer, while the master registers may hold a new setup to be used
automatically after the first DMA transfer has completed.

When the terminal count DCHCn.TCn=1 is issued, the slave registers are
automatically rewritten with the values of the master registers.

Therefore, during DMA transfer, transfer is automatically started when a new
DMA transfer setting is made for these registers and the MLEn bit of the
DCHCn register is set (however, the DMA transfer end interrupt is issued even
if DMA transfer is automatically started).

This mode is called multi link mode and is configured by DCHCn.MLEn=1.

If DMA channel n is disabled (DCHCn.ENn=0), writing to DSAH/Ln, DDAH/Ln,
DBCn stores the data to the master and slave registers.

Writing the next DMA transfer setup data to the master registers only - and to
keep the first setup data in the slave registers - is possible after

• the DMA channel n has been enabled (DCHCn.ENn=1)

and

• the first DMA trigger interrupt for channel n has occurred.

The new setup data will become effective after

• the previous DMA transfer has completed (DCHC.TCn=1, INTDMAn)

and

• the next following DMA trigger interrupt for channel n has occurred.

Note that the terminal count flag DCHC.TCn does not need to be cleared in
multi link mode (DCHC.MLEn = 1) for starting up the next DMA transfer
automatically.

Figure 8-1

shows the configuration of the buffer register.

Source \

Destination

Internal RAM

Peripherals

Internal RAM

–

1

Peripherals

1

0

Downloaded from

electronic components distributor

«
...
321
322
323
324
325
...
»

Содержание V850E/Dx3



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для V850E/Dx3

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Parker Страницы: 21

Бренд: Parker Страницы: 26

Бренд: Vageo Страницы: 2

Pearldex Series

Бренд: KaMo Страницы: 2

Бренд: A10 Networks Страницы: 2

Бренд: Partlow Страницы: 49

Бренд: Ascon tecnologic Страницы: 11

Бренд: ROBOT3T Страницы: 21

Бренд: StudioComm Страницы: 61

Бренд: zeeltronic Страницы: 13

Бренд: QD Dynamics Страницы: 64

Бренд: Lumel Страницы: 32

ZigBee Pro VT8000 Series

Бренд: Viconics Страницы: 3

Бренд: PI Страницы: 111

Бренд: WAGO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды