Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 97 / 205

background image

91

Alert Tone
Configuration

From the MAIN MENU, press

F4, F3

and then

F4

again to access this

screen.

From this screen, you can configure options for the radio’s alert tone
operation.

Function Key Descriptions

F5

- PRINT

Prints the current system configuration.

F9

- DEFAULT

Resets the fields on this screen to their default values.

Field Definitions

Master Alert Tone Control

This field allows you to enable/disable all alert tones controlled from
this and all other screens, with two exceptions. These are tones which
cannot be disabled from the RSS: MDC Select Call Alert and Quik-Call
II Select Call Alert.

If the Master Alert Tone Control is set to Disabled, none of the Alert Tones
can be enabled individually until the Master Alert Tone Control is enabled.
If you want to disable all alert tones, only the Master Alert Tone
control needs be changed. All individual tones will then be
automatically disabled.

Note:

There are two actions that will override and reset the state

of the Master Alert Tone Control feature. These are:

1. Use of the

F9

default key on any screen that has alert fields.

2. Changing the setting for the Signalling Type field on the
MDC/STAR/ATIS OPTIONS screen (

F4/F3/F7/F3

) which sets the

new signal type defaults.

When the Master Alert Tone control is re-enabled, all individual
tones will still be disabled. Therefore, the desired tones must be
turned on individually.

The default is Enabled.

DCD

MOTOROLA Radio Service Software Use

<:

keys to enable/disable feature

HT/JT1000/VISAR Model : Use <Enter> to go to next feature.
Serial:
CHANGE:RADIO:ALERT TONE CONFIG

Alert Tone Configuration
------------------------

Master Alert Tone Control.....Enabled Mandown Pre Alert.............Enabled
Power Up Alert................Enabled Tx Low Battery Alert..........Enabled
Illegal Channel Alert.........Enabled Rx Low Battery Alert.........Disabled
Timeout Timer Alert...........Enabled
Timeout Timer Pre-Alert......Disabled Low Battery Alert Intvl (sec).....120
Alert Volume Tx...................176
PL Defeat Alert...............Enabled Alert Volume Rx...................176

Scan Programming Alert........Enabled
Priority Chan Lock Alert......Enabled
PTT Tx Inhibit Alert..........Enabled

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP PRINT DEFAULT EXIT

«
...
95
96
97
98
99
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Trio Страницы: 76

Бренд: Coby Страницы: 9

Бренд: Fabco Power Страницы: 13

Бренд: Zebronics Страницы: 6

Бренд: Curtis Страницы: 6

Бренд: AWA Страницы: 25

Бренд: RCA Страницы: 15

Бренд: Daewoo Страницы: 2

Бренд: Daewoo Страницы: 46

Бренд: Roadstar Страницы: 4

Бренд: Rhythmz Страницы: 3

Бренд: NGS Страницы: 68

Бренд: NGS Страницы: 100

Бренд: Tait Страницы: 52

Бренд: Hama Страницы: 16

Бренд: Connect Systems Страницы: 13

Бренд: Parker Balston Страницы: 16

Бренд: sunjoe Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды