Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 54 / 205

background image

48

Transmit Deviation
Limit Alignment:
MDC-1200
Signalling

From the MAIN MENU, press

F2, F4

and then

F3

to access this screen.

This screen reads the radio codeplug, then displays the frequency on
the left side of the screen, and to the right of it the MDC-1200 setting.
On the far right side of the screen, the MDC-1200 softpot number is
displayed. The bar at the bottom of the screen shows the current
setting in relation to the minimum and maximum settings. Press

F6

to

toggle PTT. Press

F8

key to program the value into the radio.

Refer to your Radio Service Manual for the Transmit Deviation Limit
Alignment: MDC-1200 Signalling procedure.

Function Key
Descriptions

F6

- TOGGLE PTT

Toggles PTT.

F8

- PROGRAM VALUE

Programs the selected value into the radio.

Field Definition

New Softpot Value

This is the squelch attenuator softpot value for this frequency. The
status bar shows the relationship between this setting and the
minimum and maximum settings.

BDC

MOTOROLA Radio Service Software Use

<:

or <SHIFT>

<

<SHIFT>

:

keys

HT/JT1000/VISAR Model: to change softpot.
Serial:
SERVICE:SIG ALIGN:XMIT DEV MDC

Transmit Deviation Limit Alignment: MDC 1200 Signalling
-------------------------------------------------------

Test Current
Frequency Value

136.02500 21 New Softpot Value: 21





0 31
MIN |----+----+----+----+----+----+----+--X-+----+----+----+----| MAX

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP TOGGLE PROGRAM EXIT
PTT VALUE

!

Caution

These procedures should be attempted only by
qualified service personnel. Failure to perform
alignment procedures properly may result in seriously
degraded radio or system performance.

«
...
52
53
54
55
56
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: M/A-Com Страницы: 44

Бренд: M/A-Com Страницы: 72

MPD820 - DVD Player - 8

Бренд: Magnavox Страницы: 42

Бренд: Ubiquiti Страницы: 33

Бренд: Sirius Satellite Radio Страницы: 2

Бренд: ISKCO Страницы: 4

Бренд: Blaupunkt Страницы: 34

Бренд: Steelcase Страницы: 2

Бренд: Champion Страницы: 108

Бренд: General Страницы: 8

Бренд: Power Stroke Страницы: 48

Бренд: Axion Страницы: 25

HomePatrol - II

Бренд: Uniden Страницы: 43

Бренд: LoopTone Страницы: 5

Бренд: MAJORITY Страницы: 35

Бренд: Nanni Страницы: 80

Tiptop Audio Eurorack 200 Series

Бренд: Buchla Страницы: 2

Бренд: Atlas Copco Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды