Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 158 / 205

background image

152

Signalling Muting Condition

Use the UP/DOWN arrow keys to make your selection. The Voice
Selective Call options within the radio (MDC, Quik-Call II, and ATIS)
affect the unmuting operation of the radio. The two available
unmuting choices are Signalling “AND” and Signalling “OR”. Note that
this choice is necessary ONLY if Voice Selective Call is being programmed on
this channel.

Note:

Signalling Unmuting will be forced to OR if no Voice Selective

Call options have been selected on a particular channel. Signalling
Unmuting will be forced to AND if Voice Selective Call is enabled on
a channel with carrier squelch receive.

Set up the PL/DPL and the Voice Selective Call configuration on the
CHANNEL CONFIGURATION screen (

F4/F4

) and the Radio Squelch

Unmute/Mute field on this screen for the channel before setting up
this field.

• Use Signalling AND unmuting when setting up a channel that will

be used for Paging/Voice Selective calling ONLY.

• Use Signalling OR unmuting when setting up a channel that will

be used for normal Dispatch and Paging/Voice Selective calling.

This field will be forced is Voice Selective Calling is not enabled, or
Voice Selective Call is enabled on a channel with Carrier Squelch.

The default is OR.

Channel Slaved Auto Scan

Use the UP/DOWN arrow keys to enable/disable auto scan for the
current channel. It slaves channel scanning to a particular Rotary
Switch position, leaving the other controls available for other
functions.

Note:

If Auto-Scan is enabled when other controls (toggle switch or

side button) are already configured to control scanning, the change
will NOT be allowed.

The default is Disabled.

Signalling
“AND”

The receiving unit will unmute audio when the radio
decodes a Voice Selective Call for which it is the target
AND the unmute/mute condition shown in the Radio
Squelch Unmute/Mute field is met.

This setting is typically used where the user wants to
listen ONLY to traffic that is addressed to his/her
individual unit (i.e., a “paging only” channel position
on the radio).

Signalling “OR”

The receiving unit will unmute audio when the radio

decodes a Voice Selective Call for which it is the target
OR the unmute/mute condition shown in the Radio
Squelch Unmute/Mute field is met.

This setting should be used when a channel position is
utilized for selective call/paging as well as normal
dispatch traffic. It is advisable to limit paging functions
to a dedicated channel position (that is, use Signalling
AND muting) where possible.

«
...
156
157
158
159
160
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Hamilton/Buhl Страницы: 2

Бренд: Team Страницы: 33

Бренд: TechniSat Страницы: 267

Бренд: Memorex Страницы: 10

Бренд: Manhattan Страницы: 12

REVERY R4 WFS-58

Бренд: Sangean Страницы: 87

Бренд: Lamborghini Caloreclima Страницы: 112

Бренд: Westinghouse Страницы: 103

Бренд: Sandstrom Страницы: 76

HD Radio HDT-20

Бренд: Sangean Страницы: 15

Бренд: ZIPPER MASCHINEN Страницы: 93

Бренд: Insignia Страницы: 40

Бренд: ulsonix Страницы: 4

Бренд: Billow Technology Страницы: 90

Бренд: Vertex Standard Страницы: 63

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 32

DVD LS82 - DVD Player - 8.5

Бренд: Panasonic Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды