Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 77 / 205

background image

71

Radio
Configuration Menu

From the MAIN MENU, press

F4

and then

F3

to access this menu.

This menu allows you to access seven other screens where radio
features may be modified or adjusted to customize the radio’s
operation. Fields for unsupported options will not be visible.

Note:

The MODE SWITCH POSITION ASSIGNMENT screen cannot

be accessed for VISAR models and will not be visible when a VISAR
codeplug is in memory.

Note:

The OPTION•MATE CONFIGURATION screen can be

accessed only for HT 1000 models. This option and function key will
NOT be visible for any other models.

Typically, when you start editing a codeplug, you should access this
menu and configure the radio-wide configuration options first by
working your way through the sub-menus of this menu. This will
allow the options on other screens to reflect radio-wide options.

Function Key Descriptions

F2

-SYSTEM CONFIG

(System Configuration)

Brings up a screen from which you can customize the system
configuration for the current radio. This screen will vary depending on the
product (HT 1000, JT1000, or VISAR).

F3

-SIDE BTN CONFIG

(Side Button Configuration)

Brings up a screen from which you can configure functions for the
radio’s side buttons. This screen will vary depending on the product (HT
1000, JT1000, or VISAR).

F4

- ALERT CONFIG

(Alert Tone Configuration)

Brings up a screen from which you can configure the radio’s alert tone
operation.

F5

- OPTION MATE

(Option•Mate Configuration)

This function will be visible only for HT 1000 radios of model “C” or later.
Brings up a screen from which you can configure a model “C” or later
HT 1000 radio’s Option•Mate Plug-compatible devices. Refer to the
Option•Mate Configuration section on page 94 of this manual for
details.

DC

MOTOROLA Radio Service Software Select a function key, F1-F10.
HT/JT1000/VISAR Model :
Serial:
CHANGE:RADIO CONFIG

Radio Configuration Menu
------------------------

F1 - HELP
F2 - System Configuration
F3 - Side Button Configuration
F4 - Alert Tone Configuration
F5 - Option•Mate Configuration
F6 - Mode Switch Position Assignment
F7 - Signalling Options Menu
F8 - Scan List Channels
F9 -
F10 - EXIT

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP SYSTEM SIDE BTN ALERT OPTION SWITCH SIGNAL SCAN EXIT
CONFIG CONFIG CONFIG MATE CONFIG MENU LIST

«
...
75
76
77
78
79
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: DAPAudio Страницы: 28

Бренд: E.F. Johnson Company Страницы: 75

Бренд: CAMPAGNOLA Страницы: 120

Бренд: Briggs & Stratton Страницы: 28

DDR-63 - WIFI INTERNET RADIO-TUNERS

Бренд: Sangean Страницы: 1

Бренд: G-Prject Страницы: 16

Бренд: Predator Страницы: 24

Бренд: FEESER Страницы: 32

Бренд: Champion Страницы: 29

Бренд: Radio Shack Страницы: 48

Бренд: K&S BASIC Страницы: 13

Бренд: CMi Страницы: 156

Бренд: König Electronic Страницы: 116

Бренд: TechniSat Страницы: 112

Бренд: SOUNDMASTER Страницы: 73

Бренд: Wen Страницы: 52

Бренд: Vitek Страницы: 6

Бренд: Power Tech Generators Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды