Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 119 / 205

background image

113

STAR Configuration

From the MAIN MENU, press

F4, F3, F7

and then

F3

to access this

screen.

This screen CANNOT be accessed for JT1000 model radios. From this
screen, you can configure GE STAR signalling options.

Function Key Descriptions

F3

- STAR OPTIONS

Brings up a screen from which you can configure additional GE STAR
signalling options. This screen CANNOT be accessed for JT1000 model
radios.

F5

- PRINT

Prints the current system configuration.

F9

- DEFAULT

Resets the fields on this screen to their default values.

Field Definitions

Signalling Type

Use the UP/DOWN arrow keys to select the signalling type: MDC1200,
STAR (GE STAR) or ATIS. Once the signalling type is set, the RSS will
update the screen to reflect the appropriate options.

The default is MDC1200.

Addressing Mode

Use the UP/DOWN arrow keys to make your selection. The STAR
Addressing Mode can be set to Extended or Portable. For Extended
mode addressing, the Unit ID range is 0001 to 9999 (decimal) and for
Portable mode addressing, the Unit ID range is 0001 to 2047 (decimal).

The default is Portable.

PTT ID Code

Enter a value directly or use the UP/DOWN arrow keys to make your
selection. This field allows you to set the ID Code that is transmitted
with PTT-ID and Emergency messages. Its range depends on the
addressing mode.

The default is 2034.

DCGC

MOTOROLA Radio Service Software Use

<:

keys to enable/disable feature.

HT/JT1000/VISAR Model : Use <Enter> to go to next feature.
Serial:
CHANGE:RADIO:SIG:STAR CONFIG

STAR Configuration
------------------

Signalling Type..................STAR Emergency....................Enabled
Addressing Mode..............Portable Emergency Tx Light..........Enabled
PTT ID Code......................2034 Emergency Alert.............Enabled
Baud Rate................800 bits/sec Emergency Ack Alert.........Enabled
PL Transmit...................Enabled Silent Emergency...........Disabled
PTT ID...........................None Silent Emer w/ Voice.......Disabled
PTT Sidetone..................Enabled Channel Revert............. Enabled
Emergency Sidetone...........Disabled Priority Revert Channel.........1
Auto Timed Mute Duration (ms).....550

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP STAR PRINT DEFAULT EXIT
OPTIONS

«
...
117
118
119
120
121
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Ocean Digital Страницы: 38

Бренд: Ritron Страницы: 36

Бренд: Albrecht Страницы: 23

Бренд: Sangean Страницы: 31

Бренд: Sencor Страницы: 10

Storm Responder 5500

Бренд: Briggs & Stratton Страницы: 48

Бренд: Ericsson Страницы: 22

PULSER X010 Series

Бренд: Regin Страницы: 4

Бренд: Denver Страницы: 27

Бренд: Sangean Страницы: 69

Бренд: Icom Страницы: 16

Бренд: Midland Страницы: 40

Бренд: Roberts Страницы: 36

Бренд: iHome Страницы: 15

Бренд: Puleida Страницы: 15

Бренд: Oricom Страницы: 30

Бренд: Oricom Страницы: 34

Бренд: Mini Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды