Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 92 / 205

background image

86

Monitor Long Press Period (sec)

Enter a value directly or use the UP/DOWN arrow keys to select the
length of time that the Monitor Button must be held down to engage
Permanent Monitor mode. The valid range of values is 1 to 16 seconds.

The default is 5 seconds.

Scan
Programming
Status Scroll

Allows the operator to select a channel's status in the
scan list by scrolling through three states (Not in List,
Non-Priority, Priority) as this button is pressed. The
status of the channel is indicated by the bi-color LED.
LED OFF indicates “Not in Scan List,” LED Green
indicates “Non-Priority Status” and LED Red indicates
“Priority Status”.

Monitor/Scan
Programming
Status Scroll

Combines the Monitor function with Scan
Programming Status Scroll while in Scan Programming
mode.

Emergency
Alarm

An MDC or STAR Emergency Alarm sequence is
initiated when this button is pressed.

Phone Encode

Places the radio in Telephone Encode mode, initiating
an auto-access sequence if so programmed. Applicable to
keypad models only.

Select

Allows temporary removal of a channel from the scan
list in the Nuisance Delete Function, and performs the
Scan Programming Status Scroll function in Scan
Programming mode.

Scan/Scan
Programming
On/Off

A short press will toggle the Channel Scan mode on
and off. A long press will place the radio in the Scan
Programming mode where the scan list can be modified
by the radio operator.

Note

: In Scan Programming mode, the radio will not

unmute to channel traffic. A tone will sound to remind
the operator if the radio was left in Scan Programming
mode with no key activity for more than 20 seconds. To
complete the Operator Selectable scan functionality,
the other side button must be assigned to the Scan
Programming Status Scroll function. Refer to page 87 for
scan-related button setups.

Single Tone #1
and #2 Encode

Initiates transmission of the selected Single Tone.

Scan On/Off

Allows scan to be toggled on and off. No scan
programming is allowed with this setup.

Light Button

Allows the radio user to toggle the display/keypad
backlighting on and off on keypad-equipped radios only.

«
...
90
91
92
93
94
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: S2G Страницы: 102

Бренд: Tactic Страницы: 16

Бренд: JBL Страницы: 25

Бренд: Audiovox Страницы: 37

Бренд: CORNING Страницы: 48

Бренд: Powermate Страницы: 12

Бренд: Vertex Standard Страницы: 20

Бренд: kchibo Страницы: 5

Бренд: Teac Страницы: 12

Бренд: Redwood Страницы: 12

Бренд: Metricom Страницы: 10

Бренд: SBO Hearing Страницы: 4

SureCross DX80SRxM-H

Бренд: Banner Страницы: 4

Бренд: Ocean Digital Страницы: 9

Mini Bazooka 2.0 UBS-1484

Бренд: Ugo Страницы: 8

Бренд: Acterna Страницы: 40

StreamCaster 4000 Series

Бренд: Silvus Страницы: 155

Бренд: GENMAX Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды