Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 56 / 205

background image

50

Transmit Deviation
Limit Alignment:
Single Tone
Signalling

From the MAIN MENU, press

F2

and then

F4

twice to access this

screen.

This screen reads the radio codeplug, and allows the Single Tone
Softpot to be set on the right side of the screen. Use the UP/DOWN
arrow keys to increase/decrease the softpot value in fine mode. Use the

Shift

-UP/DOWN arrow keys for coarse or Turbo mode. A bar at the

bottom of the screen shows the current setting in relation to the
minimum and maximum settings.

F6

is used to toggle PTT, and

F8

is

used to program the new tuning value into the radio.

Note:

HT 1000 radios with model revisions of “A” are incapable of

Single Tone signalling. Only HT 1000 “B” and later models and
any model with DTMF keypads are capable of Singletone
signalling.

Refer to your Radio Service Manual for the Transmit Deviation Limit
Alignment: Single Tone Signalling procedure.

Function Key
Descriptions

F6

- TOGGLE PTT

Toggles PTT.

F8

- PROGRAM VALUE

Programs the selected value into the radio.

Field Definition

New Softpot Value

This is the squelch attenuator softpot value for this frequency. The
status bar shows the relationship between this setting and the
minimum and maximum settings.

BDD

MOTOROLA Radio Service Software Use

<:

or <SHIFT>

<

<SHIFT>

:

keys

HT/JT1000/VISAR Model: to change softpot.
Serial:
...SIG ALIGN:XMIT DEV SINGLE TONE


Transmit Deviation Limit Alignment: Single Tone Signalling
------------------------------------------------------------

Test Current
Frequency Value

136.02500 21 New Softpot Value: 21





0 31
MIN |----+----+----+----+----+----+----+--X-+----+----+----+----| MAX

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP TOGGLE PROGRAM EXIT
PTT VALUE

!

Caution

These procedures should be attempted only by
qualified service personnel. Failure to perform
alignment procedures properly may result in seriously
degraded radio or system performance.

«
...
54
55
56
57
58
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Logitech Страницы: 7

Бренд: auna multimedia Страницы: 24

Бренд: Fresh 'N Rebel Страницы: 34

Бренд: Durabrand Страницы: 28

Бренд: A2Z Ozone Страницы: 13

Бренд: Campbell Страницы: 51

Бренд: Shindaiwa Страницы: 68

Бренд: LEXIBOOK Страницы: 8

Бренд: S&C Страницы: 4

Бренд: Jensen Страницы: 2

Бренд: Hantek Страницы: 37

Бренд: Bergstrom Страницы: 15

Бренд: Curtis Страницы: 1

Бренд: AvaLAN Страницы: 8

Бренд: AvaLAN Страницы: 18

Бренд: Philips Страницы: 1

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды