Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 40 / 205

background image

34

Transmit Deviation
Limit Alignment:
Reference Softpot

From the MAIN MENU, press

F2

twice and then

F6

to access this

screen.

Reference Attenuator Alignment is required after replacement or servicing of
the Controller Board or the RF Board. This alignment procedure limits the
modulation of the baseband signal. It is used for secondary
modulation limiting.

The reference frequency is displayed on the left side of the screen. The
reference softpot is displayed on the right side of the screen. A bar at
the bottom of the screen shows the current setting in relation to the
minimum and maximum settings.

Refer to the Radio Service Manual for the Transmit Deviation Limit
Alignment: Reference Softpot procedure.

Programming Procedure

1. Press

F6

to key up the radio. (The radio’s RF output must be

terminated into a 50 ohm load.)

2. Apply the appropriate signal according to instructions in your

Radio Service Manual.

3. While transmitting, modify the Reference Attenuator setting using

the UP/DOWN arrow keys. To increase the adjustment speed, use
the Shift-UP/DOWN arrow keys.

4. A relative Tx power value will be displayed, but you must measure

the actual transmitter deviation from the service monitor.

5. Press

F6

to de-key the radio and

Tab

to move between frequency

points.

6. Press

F8

to save the new values.

BBF

MOTOROLA Radio Service Software Use

<:

or <SHIFT>

<

<SHIFT>

:

keys to change

HT/JT1000/VISAR Model: and <ENTER> to go to next softpot.
Serial:
SERVICE:XMIT ALIGN:XMIT DEV LIM REF

Transmit Deviation Limit Alignment: Reference Softpot
----------------------------------------------------
Test Current Value New Softpot Value
Frequency Channel Spacing Channel Spacing
12.5 kHz 20 kHz 12.5 kHz 20 kHz

177.97500 87 114 87 114

0 127
MIN |----+----+----+----X----+----+----+----+----+----+----+----| MAX

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP TOGGLE PROGRAM EXIT
PTT VALUE

!

Caution

This procedure should be attempted only by qualified
service personnel. Failure to perform alignment
procedures properly may result in seriously degraded
radio or system performance.

«
...
38
39
40
41
42
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Daewoo Страницы: 49

Бренд: National Instruments Страницы: 34

Бренд: Sirius XM RAdio Страницы: 26

Бренд: Radio Shack Страницы: 1

Бренд: Clas Ohlson Страницы: 28

Бренд: XM Satellite Radio Страницы: 58

Бренд: Radio Shack Страницы: 16

Бренд: GENMAX Страницы: 8

EXPLORER 1000 PLUS

Бренд: Jackery Страницы: 48

A915000JA-LI555

Бренд: Parker Balston Страницы: 14

Бренд: Emerson Страницы: 4

RobLight Ara 2 Series

Бренд: ROBLON Страницы: 4

Бренд: Midland Страницы: 10

Бренд: Makita Страницы: 28

17UC84AN-526-ARA-AA

Бренд: FCA US Страницы: 119

Бренд: Ericsson Страницы: 16

Бренд: Timex Страницы: 19

Бренд: Braven Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды