Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 159 / 205

background image

153

PAC•RT

Use the UP/DOWN arrow keys to enable/disable the operation of the
radio with a PAC•RT on this channel in conjunction with the Mode
switch. The Mode switch MUST be set up for PAC•RT in order for this option
to work. PAC•RT forces PL Transmit, Carrier Squelch Receive, and Low
Power.

The default is Disabled.

IF Bandwidth

Use the UP/DOWN arrow keys to select the IF channel bandwidth.
Valid settings are 12.5 kHz, 20 kHz, and 25/30 kHz.

The default is 25/30 kHz.

Timeout Timer

Use the UP/DOWN arrow keys to enable/disable this feature. If this
feature is enabled, radio transmission will be permitted for the time
specified in the Timeout Timer field on the SYSTEM CONFIGURATION
screen (

F4/F3/F2

). If the radio is transmitting and the time-out timer

time runs out, the radio will be automatically de-keyed and a
continuous alert tone will be generated for as long as the PTT button
is pressed. To continue transmitting, the PTT button must be released
and the radio re-keyed.

The default is Disabled.

Battery Saver

Use the UP/DOWN arrow keys to enable/disable this feature. If this
feature is enabled, battery life will be prolonged because the radio
powers down the receiver and synthesizer during periods of no
channel activity. If there is no activity, the radio will unmute for a
period of 10 seconds and then enter “sleep” mode. During the “sleep
period”, changes in condition on the channel will not be detected. The
radio will exit sleep mode periodically to check the state of the
channel. The sleep times which apply to the different channel options
are:

1. Carrier Squelch Sleep Period and PL Sleep Period in the SYSTEM

CONFIGURATION screen (

F4/F3/F2

).

2. Quik-Call II Sleep Period in the QUIK-CALL II OPTIONS screen

(

F4/F3/F7/F2

).

Note:

The default sleep periods are calculated to provide battery

savings while minimizing the chances of missing a call. If sleep
periods are increased, battery savings will also increase but the
chances of missing a call become significantly greater.

Another parameter which is important in battery saver is the Battery
Saver PL Lockout on the SYSTEM CONFIGURATION screen (

F4/F3/

F2

). When this feature is disabled, Battery Saver operates as described

above and in the description of PL Sleep Period on page 75.

When Battery Saver PL Lockout is enabled, PL will NOT be decoded when
the radio periodically comes out of sleep mode until carrier drops. Therefore,
a radio which enters sleep mode while a carrier is on the channel with
wrong PL or no PL will not unmute to another call until carrier drops.
This method of operation (not decoding PL) significantly increases
battery savings but can cause problems in some systems.

The default is Disabled.

«
...
157
158
159
160
161
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: VEF Страницы: 3

Бренд: TechniSat Страницы: 19

Бренд: Ericsson Страницы: 70

Бренд: Grundig Страницы: 34

Бренд: GAS Страницы: 214

Бренд: Sirius XM RAdio Страницы: 26

Бренд: Ocean Digital Страницы: 38

Бренд: Ritron Страницы: 36

Бренд: Denver Страницы: 80

Бренд: Wacker Neuson Страницы: 98

Бренд: kchibo Страницы: 4

Бренд: Subaru Страницы: 28

Cobra CB 29 LX LE

Бренд: Giant Страницы: 6

RoadCom-Multi Norm

Бренд: Team Electronic Страницы: 11

Бренд: P1PE Страницы: 28

Бренд: DR Страницы: 76

Бренд: Vertex Standard Страницы: 31

Бренд: Vertex Standard Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды