Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 85 / 205

background image

79

Channel Wrap-around Alert

Use the UP/DOWN arrows to select Enabled or Disabled. Depending
on the setting in the Channel Wrap-around field, the Wrap-around
Alert or No Wrap-around Alert option will be enabled.

The default is Enabled.

Note:

Channel Selector Alert and Channel Wrap-around Alert are

mutually exclusive. You must disable one before enabling the
other.

Channel Selector Alert

Use the UP/DOWN arrows to select Enabled or Disabled. When this
field is enabled, an alert tone is generated when either of the Channel
Selector buttons are pressed.

The default is Disabled.

Note:

The Channel Selector Alert and Channel Wrap-around Alert

features are mutually exclusive. You MUST disable one before
enabling the other.

Enabled

An alert is generated whenever the wrap-around occurs.

Disabled

An alert is generated whenever the user attempts to go
beyond the beginning or the end of the Channel list.

«
...
83
84
85
86
87
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

AF-650 GP Series

Бренд: GE Страницы: 138

Бренд: 4RF Страницы: 12

Бренд: 4RF Страницы: 12

Бренд: 4RF Страницы: 2

Бренд: 4RF Страницы: 2

Бренд: Olympia Страницы: 32

Бренд: Crystal Vision Страницы: 24

Бренд: lauson Страницы: 20

Бренд: LENCO Страницы: 17

Бренд: Radio Shack Страницы: 12

Бренд: Tesla Страницы: 37

Бренд: Ocean Digital Страницы: 9

Бренд: SMC Networks Страницы: 2

Бренд: Briggs & Stratton Страницы: 74

Бренд: JRC Страницы: 4

Бренд: Acoustic Research Страницы: 96

Бренд: Caliber Страницы: 18

Бренд: PRESIDENT Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды