Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 83 / 205

background image

77

VISAR
Configuration
Options (Models
with Display only)

At the MAIN MENU, press

F4, F3

and then

F2

twice to access this

screen.

This menu allows the user to access the systems configuration options
for VISAR radios only. This screen cannot be accessed for HT 1000 or
JT1000 models.

Function Key Descriptions

F5

- PRINT

Prints the current system configuration.

F9

- DEFAULT

Resets the fields on this screen to their default values.

Field Definitions

Display Power-Up State

This field allows you to specify whether the display will be in Normal
or Inverted state on radio power-up.

The default is Normal.

DCBB

MOTOROLA Radio Service Software Use

<:

keys to scroll values.

HT/JT1000/VISAR Model : H05UCD6AA4AN Use <Enter> to go to next feature.
Serial:
CHANGE:RADIO:SYS CONFIG:VISAR

VISAR CONFIGURATION OPTIONS
---------------------------

Display Power-Up State.........Normal Channel Wrap-around............Enabled
Ch. Select Lock/Display Flip.....Lock Channel Wrap-around Alert......Enabled
Channel Selector Lock Alert...Enabled Channel Selector Alert........Disabled
Auto-backlight................Enabled
Backlight Timer (sec)...............5

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP PRINT DEFAULT EXIT

Normal

The display will be readable from the front, as when the
radio is held in the hand.

Inverted

The display will be readable from the top, as when the
radio is worn on the belt.

«
...
81
82
83
84
85
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: 4RF Страницы: 15

Бренд: Curtis Страницы: 16

Бренд: Champion Страницы: 34

500936 - 704 WiFi

Бренд: Archos Страницы: 60

Бренд: LENCO Страницы: 9

Бренд: FNX Solar Страницы: 32

Бренд: Richter Страницы: 12

Бренд: Wacker Neuson Страницы: 38

Hard Gear SGE3500BSi

Бренд: DAISHIN Страницы: 28

Бренд: Oricom Страницы: 29

Бренд: Rockpals Страницы: 16

Бренд: RAFFEL SYSTEMS Страницы: 2

Бренд: Hyundai Страницы: 11

Бренд: Century Mark IV Страницы: 6

Бренд: Kenwood Страницы: 25

Бренд: Motorola Страницы: 46

ASTRO XTSTM 2500 II

Бренд: Motorola Страницы: 24

Бренд: Motorola Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды