Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 94 / 205

background image

88

Side Button
Configuration
(HT 1000 “B” and
JT1000 Models)

From the MAIN MENU, press

F4

and then

F3

twice to access this

screen.

Note:

If an Advantage™ Board is installed in the radio and Side

Button 2 is functionally used by the Advantage Board, that button
MUST be set to “Blank” to prevent dual usage.

Function Key Descriptions

F5

- PRINT

Prints the current system configuration.

F9

- DEFAULT

Resets the fields on this screen to their default values.

Field Definitions

Sidebutton Functions

Use the UP/DOWN arrow keys to select the functions for this button.
Not all functions are available on all models.

Note:

The RSS will not allow side button functions to be duplicated

on more than one button, or allow you to duplicate a function that is
assigned to another control (for example, Scan on a side button
and Channel-Slaved Auto-scan in the same radio). If Scan is
already assigned to another control, Scan-related selections will
not be displayed on this screen.

The possible functions that can be assigned to Sidebuttons 1, 2 and 3
are:

DCC

MOTOROLA Radio Service Software Use

<:

keys to adjust value.

HT/JT1000/VISAR Model : H01SDC9AA3BN Use <Enter> key to go to next feature.
Serial:
CHANGE:RADIO:SIDE BUTTON

Side Button Configuration
-------------------------

Sidebutton 1 function.................................Select Button
Sidebutton 2 function.........................................Blank
Sidebutton 3 function.......................................Monitor

Monitor Long Press Period (sec)...................................5
Permanent Monitor...........................................Enabled
Permanent Monitor Definition...........................Open Squelch
External Mandown Switch.....................................Enabled

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP PRINT DEFAULT EXIT

Blank

No function, no key chirp is sounded.

Monitor

Radio will unsquelch when this button is pressed,
allowing you to listen to activity on the channel.

RAT

An MDC Repeater Access Code will be transmitted when
this button is pressed. Available only with HT 1000 models.

«
...
92
93
94
95
96
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

airFiber AF-5XHD

Бренд: Ubiquiti Страницы: 32

Бренд: Ibiza sound Страницы: 28

Бренд: Albrecht Страницы: 52

Бренд: LENCO Страницы: 52

DPC-7400 Series

Бренд: Daewoo Страницы: 26

MrSteam CU Series

Бренд: Sussman Страницы: 34

Бренд: LENCO Страницы: 77

Бренд: MAJORITY Страницы: 16

Бренд: Mercedes-Benz Страницы: 23

Бренд: ulsonix Страницы: 19

Бренд: Jensen Страницы: 2

Бренд: I-Inc Страницы: 1

SIMRAD Navico RT1200

Бренд: Kongsberg Страницы: 21

Бренд: Whisper Tech Страницы: 98

Sure Cross MultiHop

Бренд: Banner Страницы: 2

Smart Generator

Бренд: EcoFlow Страницы: 28

Бренд: EcoFlow Страницы: 78

Бренд: Mi-T-M Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды