Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 143 / 205

background image

137

Talkback Scan

Use the UP/DOWN arrow keys to enable/disable this feature. Talkback
scan allows the radio user to “talkback” to a channel that the scanner
has locked onto which is not the currently selected channel. If the PTT
button is pressed at any time during scan, the channel the radio
transmits (or monitors) on will depend on the current radio status as
follows:

• Transmits on an active channel if the scanner is locked onto it.

• Transmits on the last active channel if Receive Hang time is in

effect.

• Transmits on the channel which it last transmitted on if Transmit

hang time is in effect.

• If no activity exists, transmission occurs on the current selected

channel. Refer also to Designated Tx Channel on page 136.

The default is Enabled.

Active Channel Tone

This feature is limited to HT 1000 “B” models with firmware version 2.06
and later. If this field is enabled on a radio having an earlier version
firmware, it will have no effect.

Use the UP/DOWN arrow keys to enable/disable this feature. If this
option is enabled, an Active Channel Tone will be generated. This tone
indicates to the user the last channel (to carry traffic) on which the
radio unmuted. When the Channel Selector is cycled through the
available channels, the tone will be sounded when the last active
channel is accessed.

The default is Disabled.

Scan Channel Lockout

Use the UP/DOWN arrow keys to enable/disable this feature. If this
option is enabled, the radio will lock out of the scan list any channel
where carrier is being received but has the wrong PL or no PL. When
the carrier drops, scanning for that channel will resume.

The default is Enabled.

PL Defeat

Use the UP/DOWN arrow keys to enable/disable this feature. If this
option is enabled, holding the Monitor button for the preset amount
of time during scan will place the radio in the Permanent Monitor
mode (PL decode defeated). The state of the Permanent Monitor mode
will always default to Carrier Squelch, and is independent from the
noise squelch setting in the SIDE BUTTON CONFIGURATION screen
(

F4/F3/F3

).

Note:

This option is valid only when the radio is in the channel

scanning mode. For operation of PL defeat during non-scan
mode, refer to the description of the SIDE BUTTON
CONFIGURATION screen on page 83.

The default is Enabled.

«
...
141
142
143
144
145
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Makita Страницы: 12

Бренд: Hama Страницы: 30

Бренд: Hama Страницы: 30

Бренд: Hama Страницы: 18

Badradio SR-500

Бренд: Hama Страницы: 5

Бренд: Hama Страницы: 42

Бренд: Hama Страницы: 46

Бренд: Hama Страницы: 64

Бренд: Hama Страницы: 66

Бренд: Hama Страницы: 29

Бренд: Hama Страницы: 50

Бренд: Tactic Страницы: 16

Бренд: F&U Страницы: 10

Бренд: NANO Страницы: 28

Бренд: ConcealFab Страницы: 22

Бренд: EGG Страницы: 52

Бренд: GPX Страницы: 2

Бренд: Radio Shack Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды