Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 96 / 205

background image

90

Permanent Monitor

Use the UP/DOWN arrow keys to enable/disable this option. If this
option is enabled, the Permanent Monitor feature will be enabled in
the radio. To enter Permanent Monitor, the radio user must hold down
the Monitor button for the time specified in the Monitor Long Press
Period field on this screen. The operation of Permanent Monitor
operates is determined by the setting in the Permanent Monitor
Definition field on this screen.

Note:

The Permanent Monitor state is NOT preserved across channel

changes or power cycling.

The default is Enabled.

Permanent Monitor Definition

Use the UP/DOWN arrows to make your selection. The field is used to
specify the squelch mode of the radio during a momentary press of the
Monitor button or in Permanent Monitor mode. The two options are:

Note:

The definitions above do NOT apply to Monitor during Scan

mode. Monitor operation during Scan is controlled by the PL Defeat
field on the SCAN CONFIGURATION screen (

F4/F3/F8/F2

).

The default is Open Squelch.

External Mandown Switch

Emergency must be enabled for this feature to work. This option enables/
disables the radio’s capability to initiate the transmission of an
emergency alarm sequence (including the ID code) when the radio is
tipped more than 60 degrees from its vertical axis. The Mandown Switch
is applicable to HT 1000 models only.

Note:

This operation is only possible when the radio is equipped with

an External Mandown Switch accessory. Emergency must be enabled
for this feature to work.

Possible Side Button
Setups for Scanning

Open Squelch

The radio will be continuously unmuted

PL Defeat

The radio will be in Carrier Squelch during Monitor.

Operator Selectable
Scan Only

Sidebutton 1 = Scan/Scan Programming On/Off
Sidebutton 2 = Scan Programming Status Scroll
Sidebutton 3 = Monitor

Operator Selectable
Scan with Monitor

Sidebutton 1 = Scan/Scan Programming On/Off
Sidebutton 2 = Monitor/Scan Programming Status Scroll
Sidebutton 3 = Any other function

Operator Selectable
Scan with Nuisance
Delete

Sidebutton 1 = Scan/Scan Programming On/Off
Sidebutton 2 = Select
Sidebutton 3 = Any other function

Scan On/Off Only

Sidebutton 1 = Scan On/Off

Sidebutton 2 = Any other function
Sidebutton 3 = Any other function

Scan On/Off with
Nuisance Delete

SidebButton 1 = Scan On/Off
Sidebutton 2 = Select
Sidebutton 3 = Monitor

«
...
94
95
96
97
98
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Powermate Страницы: 12

Бренд: Generac Power Systems Страницы: 20

Бренд: Goodmans Страницы: 2

Yakumo DVD Travelle

Бренд: YAKUMO Страницы: 40

Бренд: Yaesu Страницы: 32

Бренд: Sangean Страницы: 116

Бренд: Ubiquiti Страницы: 28

Бренд: Shindaiwa Страницы: 52

Бренд: Sylvania Страницы: 24

Бренд: Firman Страницы: 57

Бренд: Milwaukee Страницы: 11

Бренд: Campbell Страницы: 130

Бренд: FUXTEC Страницы: 83

Бренд: kchibo Страницы: 2

Бренд: I-Inc Страницы: 1

Бренд: Denver Страницы: 1

Бренд: Schulz Страницы: 64

Бренд: Yamakoyo Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды