Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 131 / 205

background image

125

DTMF Phone List
(JT1000 and VISAR
Models only)

From the MAIN MENU, press

F4, F3, F7

,

and then

F5

to access this

screen.

This screen can be accessed only for models with DTMF keypads. Brings up
a screen from which you can configure DTMF options.

Function Key Descriptions

F2

- DTMF CONFIG

This function will be visible only for VISAR models. Brings up a screen
from which you can configure additional DTMF options.

F5

- PRINT

Prints the current system configuration.

F9

- DEFAULT

Resets the fields on this screen to their default values.

Field Definitions

DTMF Tx Pre-Time

Enter a value directly or use the UP/DOWN arrow keys to make your
selection. The is the time period that carrier or carrier with PL (if on a
PL channel) will be sent before the first DTMF digit is transmitted. The
value is expressed as a multiple of 25 ms, ranging from 25 ms to 6.375
seconds.

The default is 250 ms.

DTMF Digit Duration

Enter a value directly or use the UP/DOWN arrow keys to make your
selection. This is the actual time duration for which DTMF tones are
transmitted on the channel for a single digit during auto-dial, or
manual dial if a timed tone duration is selected. The valid range is 4.12
to 1050.6 ms in 4.12-ms increments. A value of zero is NOT allowed.

The default is 152.44 ms.

DCGE

MOTOROLA Radio Service Software Use edit keys to modify entry.
HT/JT1000/VISAR Model : Use <Enter> to go to next feature.
Serial:
CHANGE:RADIO:SIG:DTMF

DTMF PHONE LIST
---------------





DTMF Tx Pre-Time.......... 250 ms DTMF Access Code..............8888
DTMF Digit Duration.....152.44 ms DTMF De-Access Code...........9999
DTMF Inter-Digit Delay..103.00 ms

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP DTMF PRINT DEFAULT EXIT
CONFIG

«
...
129
130
131
132
133
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: VEF Страницы: 3

Бренд: Westfalia Страницы: 34

Бренд: Denver Страницы: 92

Бренд: GENERGY Страницы: 90

Бренд: Laser Страницы: 9

Бренд: Ranger Electronic Страницы: 11

Бренд: SOUNDMASTER Страницы: 73

Бренд: Acoustic Research Страницы: 96

PC0422507 Powermate

Бренд: Coleman Страницы: 8

Бренд: Harman Страницы: 20

DVDLS80 - PORTABLE DVD PLAYER

Бренд: Panasonic Страницы: 32

Бренд: Sytech Страницы: 4

Бренд: DMB Страницы: 24

RF-DAB-BEDSIDE1

Бренд: Renkforce Страницы: 76

Бренд: Mini Страницы: 2

WhisperWatt DCA300SSC

Бренд: MULTIQUIP Страницы: 104

Power Ultra-Silent DCA-45USI

Бренд: MULTIQUIP Страницы: 82

Бренд: MULTIQUIP Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды