Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 95 / 205

background image

89

Monitor Long Press Period (sec)

Enter a value directly or use the UP/DOWN arrow keys to select the
length of time that the Monitor Button must be held down to engage
Permanent Monitor mode. The valid range of values is 1 to 16 seconds.

The default is 5 seconds.

Scan
Programming
Status Scroll

Allows the operator to select a channel's status in the
scan list by scrolling through the three states (Not in List,
Non-Priority, Priority) as this button is pressed. The
status of the channel is indicated by the bi-color LED.
LED OFF indicates “Not in Scan List”, LED Green
indicates “Non-Priority Status” and LED Red indicates
“Priority Status”.

Monitor/Scan
Programming
Status Scroll

Combines the Monitor function with Scan Programming
Status Scroll while in Scan Programming mode.

Select

Allows the radio user to temporarily remove a channel
from the scan list in the Nuisance Delete function, and
performs the Scan Programming Status Scroll function in
Scan Programming mode.

Scan/Scan
Programming
On/Off

A short press will toggle the Channel Scan mode on and
off. A long press will place the radio in the Scan
Programming mode, where the scan list can be modified
by the radio operator.

Note:

In Scan Programming mode, the radio will not

unmute to channel traffic. A tone will sound to remind
the operator if the radio has been left in the Scan
Programming mode with no key activity for more than
20 seconds. To complete the Operator Selectable scan
functionality, the other side button must be assigned to the
Scan Programming Status Scroll function. Scan-related
button setups can be found on the following page.

MSPL Select

Allows the user entry/exit to the Multiple Selectable PL/
DPL entry mode. Available with JT1000 models only.

Note:

This function allows the user to substitute the

squelch coding on one channel onto another channel.
Available only on Sidebutton 2 of JT1000 models.

Single Tone #1
and #2 Encode

Initiates transmission of the selected Single Tone.

Scan On/Off

Allows scan to be toggled on and off. No scan
programming is allowed with this setup.

Light

Allows toggling of the keypad backlighting on and off on
keypad-equipped radios only.

«
...
93
94
95
96
97
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Olympus Страницы: 5

Бренд: Parker Страницы: 58

Бренд: QFX Страницы: 2

Бренд: Audiovox Страницы: 28

Бренд: Generac Portable Products Страницы: 36

Бренд: Xoro Страницы: 50

Бренд: Powermate Страницы: 12

Бренд: FEESER Страницы: 32

Бренд: K&S BASIC Страницы: 13

Бренд: Parker Страницы: 30

Бренд: Olin Страницы: 26

Бренд: Cobra Страницы: 27

Бренд: K&S BASIC Страницы: 23

Бренд: GPX Страницы: 12

Бренд: Yaesu Страницы: 3

Бренд: Onan Страницы: 28

Бренд: Ericsson Страницы: 16

Бренд: H.F.Prints Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды