Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 142 / 205

background image

136

Priority Channel Unmute

To enable this feature, Quik-Call Scan and MDC Decode must be enabled to
permit scanning of Selective Call on a priority channel. When this feature
is enabled, the unmuting logic of the MDC or Quik-Call II decode will
be forced to be true on the priority channel.

The unmuting logic is only set if an activity has previously been
detected on a non-priority channel. After that, detection of channel
activity alone on the priority channel will cause the radio to lock on
to the priority channel and drop the non-priority channel. This is to
prevent an ”audio hole” on a non-priority channel from annoying the
user.

The default is Enabled.

Note:

Make sure you consider if Selectable Channel Unmute would be

more appropriate for a given situation. Selectable Channel Unmute
is less restrictive and will cause the radio to unmute to more
traffic than Priority Channel Unmute.

Priority Channel Definition

Use the UP/DOWN arrow keys to make your selection. The setting in
this field determines whether the priority channel is a certain fixed
channel or priority follows the selected channel.

The default is Fixed.

Fixed Priority Channel

Use the UP/DOWN arrow keys to make your selection. The setting in
this field is used as the priority channel when the priority channel
definition is fixed. Only channels marked as “Programmed” on the
CHANNEL CONFIGURATION screen (

F4/F4

) will be shown as valid

selections.

The default is Channel 1.

Designated Tx Channel

Use the UP/DOWN arrow keys to enable/disable this feature. If this
option is enabled and if the PTT or Monitor buttons are pressed at any
time during scan, transmission or monitoring will occur on this
channel. The valid range is 1 to 16, corresponding to channels 1
through 16 respectively. A value of Disabled is also available. Only
channels marked as “Programmed” on the CHANNEL CONFIGURATION
screen (

F4/F4

) will be shown as valid selections.

The default is Disabled.

«
...
140
141
142
143
144
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Wacker Neuson Страницы: 36

Бренд: Wacker Neuson Страницы: 58

Бренд: Wacker Neuson Страницы: 84

Бренд: Wacker Neuson Страницы: 40

Бренд: Lanzar Страницы: 12

Бренд: MCP Страницы: 4

Бренд: RINCO ULTRASONICS AG Страницы: 54

Бренд: Philco Страницы: 7

Бренд: Sangean Страницы: 24

Бренд: Hama Страницы: 50

Бренд: Bush Страницы: 24

Бренд: Champion Страницы: 30

Бренд: MIOX Страницы: 82

Warwick W-59-IP

Бренд: Fisher Страницы: 20

Бренд: Dr.X Works Страницы: 17

Бренд: Koshin Страницы: 36

Бренд: Sandstrom Страницы: 124

Бренд: Banner Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды