Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 107 / 205

background image

101

Sleep Period (ms)

Enter a value directly or use the UP/DOWN arrow keys to specify the
radio’s “sleep period” when it is in battery-saver mode. For a channel
with the Quik-Call II Decode option enabled, the sleep period is related to the
first tone and must be programmed so that pages are not lost. The default
sleep period of 60 ms is calculated to be safe for a system with a tone
duration of 500 ms or greater. Valid values for Sleep Period range from
five to 1050 ms in five-ms increments.

The default is 60 ms.

Auto Reset

Use the UP/DOWN arrow keys to enable/disable this timer. This
option allows you to use the Auto-Reset timer for Quik-Call II
signalling.

The Auto-Reset timer allows a two-way conversation to follow a
Selective Call. When the conversation ends, the radio will
automatically be returned to Page mode. The auto reset timer specified
on the RADIO SYSTEM CONFIGURATION screen (

F4/F3/F2

) is initiated

after the Selective Call is received and the Alert Tone sequence is
sounded. The radio will return to Page mode (signalling squelch) if:

• There is a period of inactivity (no carrier) on the channel for the

duration of the Auto Reset timer; and

• No PTT presses occur for the duration of the timer.

If carrier is detected or PTT is pressed, the timer will be reset and
restarted.

Note:

The timer is common to both Quik-Call and MDC signalling

systems.

The default is Enabled.

QC Select Call LED

Use the UP/DOWN arrow keys to enable/disable this option. If this
feature is enabled, the Receive Select Call LED will flash when a Select
Call (either a Quik-Call II or MDC Select Call) is received.

The default is Enabled.

«
...
105
106
107
108
109
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Axxion Страницы: 3

Бренд: Garmin Страницы: 11

Бренд: Logitech Страницы: 7

Бренд: Ubiquiti Страницы: 36

Бренд: SOUNDMASTER Страницы: 5

Бренд: ZIPPER MASCHINEN Страницы: 151

Бренд: Manta Страницы: 16

SDMO DIESEL 4000 C5

Бренд: Kohler Страницы: 222

Бренд: Sandstrom Страницы: 124

Бренд: GME Страницы: 39

Lowrance LVR-880EU

Бренд: Navico Страницы: 60

Бренд: ASCO POWER TECHNOLOGIES Страницы: 18

Бренд: Midland Страницы: 10

Бренд: Hyundai Страницы: 11

Бренд: Hyundai Страницы: 29

Бренд: Hyundai Страницы: 31

Бренд: Hyundai Страницы: 120

Бренд: Hyundai Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды