Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 113 / 205

background image

107

Channel Revert

This field will be visible only if the Emergency field on this screen is set to
Enabled. Use the UP/DOWN arrow keys to enable/disable this option.
If this feature is enabled, emergency channel revert mode operation
will be enabled in the radio.

This mode of operation will cause the radio to change from the
selected channel to the specified Revert channel when the Emergency
button is pressed. After the Emergency message is transmitted and the
Acknowledgment is received, the radio will return to the selected
channel.

Note:

The MDC/STAR/ATIS Decode field on the CHANNEL

CONFIGURATION screen (

F4/F4

) must be set to Enabled in order for

the radio to be able to decode the Emergency Ack that is generated
from the MDC fixed equipment. This feature needs to be enabled
only on the Emergency Revert channel and only when
Emergency Revert is in use.

The default is Disabled.

Priority Revert Channel

This field will be visible only if the Emergency field on this screen is set to
Enabled. Use the UP/DOWN arrow keys to make your selection or enter
the desired number directly for the channel to be used for emergency
transmission when Channel Revert mode is enabled.

The valid range of channels is 1 through the maximum number of
channels allowed in the radio. Only channels marked as
“Programmed” in the CHANNEL CONFIGURATION screen (

F4/F4

)

will be displayed as possible selections.

The default is 1.

Note:

If an Advantage™ Board is installed in the radio and the

Emergency button (orange top button) is functionally used by the
Advantage Board, that button must be set to “Blank” to prevent dual
usage.

«
...
111
112
113
114
115
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: A2Z Ozone Страницы: 13

Бренд: All-Power Страницы: 33

Бренд: Sirius Satellite Radio Страницы: 2

Бренд: GPX Страницы: 16

Бренд: Ramsond Страницы: 24

Бренд: Master Tailgaters Страницы: 6

Бренд: Champion Страницы: 108

Бренд: LENCO Страницы: 25

Бренд: Hameg Страницы: 28

Бренд: Premier Страницы: 16

Бренд: Roberts Страницы: 2

Бренд: Insignia Страницы: 2

Бренд: Subaru Страницы: 28

CX789 - Digital AM/FM/NOAA Radio

Бренд: Coby Страницы: 6

Juice Go SJUGOBL15E

Бренд: Sandstrom Страницы: 88

Бренд: Ocean Digital Страницы: 14

Бренд: Oakcastle Страницы: 24

Бренд: Uniden Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды