Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 91 / 205

background image

85

Side Button
Configuration
(VISAR only)

From the MAIN MENU, press

F4

and then

F3

twice to access this

screen.

This screen can be accessed for VISAR models only. It allows you to assign
functionality to the side buttons of a VISAR radio.

Function Key Descriptions

F5

- PRINT

Prints the current system configuration.

F9

- DEFAULT

Resets the fields on this screen to their default values.

Field Definitions

Sidebutton Functions

Use the UP/DOWN arrow keys to select the functions for this button.
Not all functions are available on all models.

Note:

The RSS will NOT allow side button functions to be duplicated

on more than one button, or allow you to duplicate a function that is
assigned to another control (for example, Scan on a side button
and Channel-Slaved Auto Scan in the same radi. If Scan is already
assigned to another control, Scan-related selections will not be
displayed among the choices.

The possible functions that can be assigned to Sidebuttons 1 and 2 are
detailed below:

DCC

MOTOROLA Radio Service Software Use

<:

keys to adjust value.

HT/JT1000/VISAR Model : H05SDD9AA4AN Use <Enter> key to go to next feature
Serial:
CHANGE:RADIO:SIDE BUTTON

Side Button Configuration
-------------------------

Sidebutton 1 function..................................Light Button
Sidebutton 2 function.......................................Monitor

Monitor Long Press Period (sec)...................................5
Permanent Monitor...........................................Enabled
Permanent Monitor Definition...........................Open Squelch

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP PRINT DEFAULT EXIT

Blank

No function, no key chirp is sounded.

Monitor

Radio will unsquelch when this button is pressed,
allowing you to listen to activity on the channel.

RAT

An MDC Repeater Access Code will be transmitted
when this button is pressed.

«
...
89
90
91
92
93
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Garmin Страницы: 24

Бренд: Icom Страницы: 15

Бренд: Rainier Страницы: 27

Бренд: Vertex Standard Страницы: 20

Бренд: kchibo Страницы: 5

Бренд: Icar Страницы: 2

Sure Cross MultiHop H3E-NB-KR

Бренд: Banner Страницы: 8

Бренд: ZIPPER MASCHINEN Страницы: 42

Бренд: Teac Страницы: 100

Бренд: Eton Страницы: 25

Onan GenSet 3.ORDJA

Бренд: McGraw-Edison Страницы: 159

Бренд: Shindaiwa Страницы: 68

IntelliChlor SCG

Бренд: Pentair Pool Products Страницы: 12

Бренд: Rally Страницы: 4

Бренд: Roberts Страницы: 2

Бренд: Oricom Страницы: 29

Бренд: Sangean Страницы: 151

Бренд: I.SOUND Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды