Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 161 / 205

background image

155

Singletone on PTT

Use the UP/DOWN arrow keys to enable/disable this feature. If this
feature is enabled, Single Tone 1 will be enabled as defined on the
SINGLETONE CONFIGURATION screen (

F4/F3/F7/F4

) on this channel

whenever PTT is pressed. A sidetone can also be enabled on the
SIDEBUTTON CONFIGURATION screen (

F4/F3/F3

) if desired so that

the user will not talk while the Single Tone transmission is in progress.

Note:

Singletone on PTT is incompatible with PTT-ID functions

(MDC, STAR, ATIS, DTMF ANI).

The default is Disabled.

Singletone on Side buttons

Use the UP/DOWN arrow keys to enable/disable this feature. If this
feature is enabled, Single Tone 1 or 2 will be transmitted as defined on
the SINGLETONE CONFIGURATION screen (

F4/F3/F7/F4

) on this

channel by pressing a side button.

Note:

This side button must be defined for Single Tone on the

SIDEBUTTON CONFIGURATION screen (

F4/F3/F3

).

The default is Disabled.

«
...
159
160
161
162
163
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Magnavox Страницы: 2

Бренд: RACOM Страницы: 16

Бренд: CAMPAGNOLA Страницы: 120

Бренд: Logitech Страницы: 7

Бренд: Denver Electronics Страницы: 14

Бренд: GAS Страницы: 214

Бренд: Alba Страницы: 10

Бренд: PURE Страницы: 120

Бренд: Talkpod Страницы: 12

Бренд: King Canada Страницы: 11

PORTABLE GENERATORS

Бренд: Gillette Страницы: 6

Бренд: LEXIBOOK Страницы: 64

Бренд: Curtis Страницы: 15

Бренд: Toyama Страницы: 20

Бренд: Philips Страницы: 16

Бренд: Klein Tools Страницы: 20

Бренд: Lutema Страницы: 12

Бренд: KingCraft Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды