Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 82 / 205

background image

76

Flashing LED

Use the UP/DOWN arrow keys to set the field to Disabled, Channel
Busy, Low Battery, or Chan-Busy/Low-Batt.

The default is Chan-Busy/Low-Batt.

Quick Key Override

Use the UP/DOWN arrow keys to enable/disable PTT Quick Key
Override mode. If this feature is enabled and two PTT activations occur
within one second of each other, this feature will override the transmit
inhibit option and allow the radio to transmit over the “Channel
Busy” condition.

The default is Enabled.

Tx Inhibit Monitor Function

Use the UP/DOWN arrow keys to enable/disable the normal
monitoring of channels when Transmit Inhibit On Busy Channel is
enabled.

The default is Enabled.

Battery-Saver PL Lockout

Use the UP/DOWN arrow keys to enable/disable this feature. If this
feature is enabled, PL will not be decoded when the radio periodically
comes out of sleep mode until carrier drops. Therefore, a radio which
enters sleep mode while a carrier is on the channel with wrong PL or
no PL will not unmute to another call until carrier drops.

Note:

This method of operation (not decoding PL) significantly

increases battery savings, but can cause problems in some
systems. Use of Battery Saver should be carefully tested in the
customer system when the option is enabled.

The default is Disabled.

Low Battery

The LED will blink when the battery voltage falls below a
predetermined value.

Channel Busy

The LED will blink when a carrier is present on a receive-
PL channel.

«
...
80
81
82
83
84
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: A2Z Ozone Страницы: 13

Бренд: ConcealFab Страницы: 22

Бренд: EGG Страницы: 52

Бренд: Ryobi Страницы: 68

Бренд: Shindaiwa Страницы: 42

Бренд: Uniden Страницы: 12

Бренд: bem wireless Страницы: 5

Бренд: ZIPPER MASCHINEN Страницы: 42

Бренд: Radio Shack Страницы: 16

Бренд: Sirius Satellite Radio Страницы: 36

Бренд: Manta Страницы: 16

Бренд: Sandstrom Страницы: 140

Бренд: Feider Machines Страницы: 80

IntelliHeat ST 115

Бренд: Pace Страницы: 20

Бренд: LENCO Страницы: 91

Бренд: Curtis Страницы: 15

Бренд: Vertex Standard Страницы: 4

Бренд: Vertex Standard Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды