Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 38 / 205

background image

32

Transmit Deviation
Limit Alignment

From the MAIN MENU, press

F2

twice and then

F5

to access the

TRANSMIT DEVIATION LIMIT screen.

This procedure is used to correct for deviation sensitivity versus RF
frequency variations in the VCO. The transmit and receive bands are
divided into frequency zones with a calibration point (value) in each
zone.

Note:

Compensation for each of these points must be checked

and adjusted if the VCO is replaced.

The status bar at the bottom of the screen shows the relationship
between the softpot value for each frequency as a value between the
minimum and maximum settings.

Refer to your Radio Service Manual for the Transmit Deviation Limit
Alignment procedure.

Programming Procedure

1. Press

F6

to key up the radio. (The radio’s RF output must be

terminated into a 50 ohm load.)

2. Apply the appropriate signal according to instructions provided in

your Radio Service Manual. While transmitting, modify the VCO
Attenuator setting with the UP/DOWN arrow keys.

3. Measure the actual RF power with a service monitor.

4. Press

F6

to de-key the radio.

5. Press

F8

to save the new value.

6. Use

Tab

to move between frequency points, repeating steps 1

through 5 for each field.

BBE

MOTOROLA Radio Service Software Use

<:

or <SHIFT>

<

<SHIFT>

:

keys to change

HT/JT1000/VISAR Model: and <ENTER> to go to next softpot.
Serial:
SERVICE:XMIT ALIGN:XMIT DEV LIM

Transmit Deviation Limit Alignment
----------------------------------
Test Current
Frequency Value New Softpot Value

450.02500 175 175
465.22500 175 175
475.22500 180 180
484.97500 180 180
500.27500 180 180
511.97500 180 180
519.97500 180 180

0 255
MIN |----+----+----+----X----+----+----+----+----+----+----+----| MAX

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP TOGGLE PROGRAM EXIT
PTT VALUE

!

Caution

This procedure should be attempted only by qualified
service personnel. Failure to perform alignment
procedures properly may result in seriously degraded
radio or system performance.

«
...
36
37
38
39
40
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Jackery Страницы: 20

Бренд: QFX Страницы: 6

Бренд: Polaroid Страницы: 44

Бренд: perfect pro Страницы: 32

Бренд: K&S BASIC Страницы: 14

Бренд: Wacker Neuson Страницы: 42

Бренд: Albrecht Страницы: 9

Бренд: Homelite Страницы: 68

Бренд: Teac Страницы: 100

Бренд: Master Tailgaters Страницы: 6

Бренд: X4-TECH Страницы: 18

Бренд: Clatronic Страницы: 14

Бренд: Vertex Standard Страницы: 34

Viking VM600 Series

Бренд: E.F. Johnson Страницы: 188

Бренд: Swissvoice Страницы: 104

Бренд: Champion Страницы: 28

Бренд: ApexRadio Страницы: 2

Бренд: Onan Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды