Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 52 / 205

background image

46

Signalling
Alignment Menu

From the MAIN MENU, press

F2

and then

F4

to access this screen.

This screen allows you to access the deviation alignment screens for
MDC, DTMF, and Single Tone Deviation signalling.

Note:

The choices available on this screen vary depending on

the model of the radio being serviced.

HT 1000 radios with model revisions of “A” are incapable of DTMF
signalling. Only HT 1000 “B” and later models, and VISAR “A7”
models, and JT1000 models are capable of DTMF signalling and
need DTMF signalling alignment.

JT1000 models are incapable of MDC, STAR, and ATIS signalling
and do not need MDC alignment.

HT 1000 models with model revisions of “A” are incapable of Single
Tone signalling. Only HT 1000 “B” and later models, VISAR
models, and JT1000 models are capable of Single Tone signalling
and need Single Tone signalling alignment.

BD

MOTOROLA Radio Service Software Please make sure <Caps Lock> is not
HT/JT1000/VISAR Model: enabled before pressing F2-F9.
Serial:
SERVICE:SIG ALIGN


Receive Alignment Menu
----------------------

F1 - HELP
F2 -
F3 - MDC Deviation Alignment
F4 - DTMF Deviation Alignment
F5 - Single Tone Deviation Alignment
F6 -
F7 -
F8 -
F9 -
F10 - EXIT


F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP MDC DTMF SINGLTN EXIT
DEV DEV DEV

!

Caution

These procedures should be attempted only by
qualified service personnel. Failure to perform
alignment procedures properly may result in seriously
degraded radio or system performance.

«
...
50
51
52
53
54
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Hama Страницы: 30

Бренд: Hama Страницы: 30

Бренд: Hama Страницы: 18

Badradio SR-500

Бренд: Hama Страницы: 5

Бренд: Hama Страницы: 42

Бренд: Hama Страницы: 46

Бренд: Hama Страницы: 64

Бренд: Hama Страницы: 66

Бренд: Hama Страницы: 29

Бренд: Hama Страницы: 50

Бренд: Radio Shack Страницы: 1

Бренд: Radio Shack Страницы: 2

Бренд: Radio Shack Страницы: 4

Бренд: Salora Страницы: 35

Бренд: Powermate Страницы: 12

Бренд: Sonoro Страницы: 136

Бренд: Icar Страницы: 28

Бренд: K&S BASIC Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды