Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 98 / 205

background image

92

Power-Up Alert

Use the UP/DOWN arrow keys to enable/disable the Power-Up Alert
tone that the radio emits when it powers up. The frequency of the
Power-Up Alert tone depends on the outcome of the radio’s self-test
routine. If the radio’s circuitry passes the self-test, the Power-Up Alert
tone will be sounded at 900 Hz (high tone) for 75 ms. If the self-test
fails in a non-fatal fashion, the Power-Up Alert tone will be sounded at
300 Hz (low tone) for 75 ms, and the radio will continue to operate.

The default is Enabled.

Illegal Channel Alert

Use the UP/DOWN arrow keys to enable/disable this feature. When
this feature is enabled and a non-programmed channel is selected, an
alert tone will be emitted to warn the user that it is invalid.

The default is Enabled.

Timeout Timer Alert

Use the UP/DOWN arrow keys to enable/disable the transmit Timeout
Timer Alert feature. If this feature is enabled, this alert tone will be
sounded from the time that the timeout timer (TOT) expires until the
time that the PTT button is released.

The default is Enabled.

Timeout Timer Pre-Alert

Use the UP/DOWN arrow keys to enable/disable the Timeout Timer
Pre-alert feature. If this feature is enabled, a pre-alert tone will be heard
four seconds before the timer times out.

The default is Disabled.

PL Defeat Alert

Use the UP/DOWN arrow keys to enable/disable this feature. If this
feature is enabled, the radio will generate an alert before it enters the
PL Defeat mode. The radio will enter Permanent PL Defeat mode when
the Monitor button is held down for more than five seconds.

The default is Enabled.

Scan Programming Alert

Use the UP/DOWN arrow keys to enable/disable this feature. If this
feature is enabled, an alert will be generated when the radio user enters
or exits Scan Programming mode.

The default is Enabled.

Priority Channel Lock Alert

Use the UP/DOWN arrow keys to enable/disable this feature. If this
feature is enabled, an alert tone will be generated while in Priority Scan
and unmuting on the priority channel.

The default is Enabled.

PTT Tx Inhibit Alert

Use the UP/DOWN arrow keys to enable/disable this feature. If this
feature is enabled, an alert tone will be generated if the radio user
presses the PTT button when the radio’s transmission is inhibited (ex.
Rx only channel, busy channel, etc.).

«
...
96
97
98
99
100
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Mag One Страницы: 8

Бренд: GOWIN Страницы: 2

Бренд: Ibiza sound Страницы: 28

Бренд: nedis Страницы: 72

Бренд: Ocean Digital Страницы: 27

Бренд: DAEWOO ELECTRONICS Страницы: 14

Бренд: Ranger Electronic Страницы: 11

Бренд: Hytera Страницы: 47

Бренд: Sencor Страницы: 14

Бренд: Champion Power Equipment Страницы: 29

Бренд: Porter-Cable Страницы: 24

Бренд: ISOUND Страницы: 3

Бренд: ROBLON Страницы: 8

Бренд: ROBLON Страницы: 8

Бренд: AADCO Страницы: 72

Бренд: Digi Страницы: 67

Бренд: Curtis Страницы: 29

Бренд: Curtis Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды