Motorola HT 1000 Скачать руководство пользователя | Manualshive

Страница: 134 / 205

background image

128

DTMF ANI (Automatic Number
Identification) Type

Use the UP/DOWN arrow keys to make your selection. DTMF ANI is a
PTT-ID function implemented with DTMF tones. It is available on a
channel-by-channel basis, that is, the PTT-ID field on the CHANNEL
CONFIGURATION screen (

F4/F4

) must be enabled for the desired channel.

But it cannot be mixed with any other type of PTT-ID function (MDC
or STAR PTT-ID, or Single Tone on PTT) on separate channels. The
settings available for this field are:

DTMF ANI Code

Enter a value directly or use the UP/DOWN arrow keys to make your
selection. This field is used to specify the DTMF digits that will be
transmitted when DTMF ANI is selected. The code can be a maximum
of eight DTMF digits. Any DTMF digit can be used (0 - 9, *, and #).

DTMF Pre-Emphasis

Use the UP/DOWN arrow keys to enable/disable the use of the pre-
emphasis circuitry for the encoded DTMF tones.

DTMF Sidetone Type

Use the UP/DOWN arrow keys to make your selection. This field is
used to specify the type of sidetone to be used during DTMF digit
encode. The type of sidetone allowed will depend on the setting in the
DTMF Tone Type field on this screen and the type of dialing (manual or
automatic) used. The table below summarizes the type of sidetone that
can be expected:

Note:

When timed DTMF tones are used, DTMF sidetones are not

possible. Therefore, the choices are limited by the RSS.

Key up

ANI code is transmitted when PTT is pressed. User
must wait until ANI code is transmitted before
speaking.

Dekey

ANI code is transmitted when PTT is released.

Key up/Dekey

ANI code is transmitted upon PTT press and again
upon PTT release.

None

DTMF ANI disabled.

DTMF

Sidetone Type

DTMF Tone

Type

Sidetone for
Manual Dial

Sidetone for

Auto-dial

900 Hz

Continuous

900 Hz

900 Hz

DTMF Tones

Continuous

DTMF Tone

DTMF Tone

900 Hz

Timed

900 Hz

900 Hz

DTMF Tones

Timed

Combination is
not supported

Combination is
not supported

«
...
132
133
134
135
136
...
»

Содержание HT 1000














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 1000

Бренд: Rainier Страницы: 27

Бренд: Eton Страницы: 11

Бренд: Shindaiwa Страницы: 52

Бренд: Scheppach Страницы: 44

Бренд: Grace Digital Страницы: 52

Бренд: lauson Страницы: 20

Бренд: LENCO Страницы: 17

Бренд: Brigmton Страницы: 10

Бренд: International Receiver Company Страницы: 31

Бренд: Hubner Страницы: 54

Бренд: Grundig Страницы: 162

Бренд: LENCO Страницы: 77

Бренд: Icom Страницы: 6

Бренд: Honda Страницы: 59

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренд: Scott Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды