mori seiki ZL-153 Скачать руководство пользователя страница 300

Страница: 300 / 561

B-72 MANUAL OPERATION

When the tailstock is moved to the position where

the scribed line (marker) on the upper face of the

tailstock is aligned with the front edge of the saddle

right side cover of turret 1, the tailstock is positioned

at the joint position.

13)

Press the TSUCLP switch.

The tailstock is unclamped and the joint pin extends

from the tailstock so that it is connected to the

saddle.

The indicator in the TSUCLP switch is lit.

14)

By turning the manual pulse generator, move the

turret 1 Z-axis until the marker at the moving side is

correctly aligned with the marker at the fixed side,

which indicates the near zero point.

The marker is provided for each of the axes.

15)

Move the turret 1 Z-axis 2 to 3 mm (approximately a

half of ball screw lead) in the direction opposite to

the zero return direction by turning the manual pulse

generator.

16)

Select the zero return mode (

) with the MODE

selection switch.

Tailstock

Saddle right side cover

Turret 1

TSCLP

TSTMOD

TSUCLP

Move the Z-axis until
they are aligned.

Marker at the fixed side

Marker at the moving side

NOTE

Marker at the fixed side

Marker at the moving side

Zero return direction

2 to 3 mm

MODE

MEM

MDI

TAPE

EDIT

JOG

RPD

ZRN

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды