mori seiki ZL-153 Скачать руководство пользователя страница 361

Страница: 361 / 561

CHUCKING C-23

20)

Chuck the ring.

When chucking the ring for shaping the soft

jaws, exercise due care to ensure that your

fingers will not get trapped.

Fit the ring on the chuck so that it is not tilted.

21)

Close the front door.

22)

Display the OPERATION PANEL screen.

Page A-126 (7-7-1)

23)

Set the chuck clamping direction to the I.D.

chucking.

For chuck 2, page 2 of the OPERATION PANEL

screen is used to the selection of clamp direction.

Page B-39 (7-4)

24)

Set "INVALID" for CHUCK STROKE END (chuck

jaw stroke end detection function) using the cursor

control keys.

For the selection of valid/invalid of chuck 2

confirmation switch, page 2 of the OPERATION

PANEL screen is used.

The STATUS indicator

[CHCL]

is lit.

For chuck 2, the status indicator

[HEADSTOCK 2

CHUCK CLAMP]

on the option panel is lit.

25)

Check for interference by following steps 13) to 15).

26)

After making sure that the spindle can be rotated

without interference, close the front door.

27)

Start the spindle manually.

Page B-32 (7-2)

28)

Set the required spindle speed.

Determine the spindle speed by considering the

soft jaw height, diameter to be cut, and the tool

material.

CAUTION

NOTE

NOR

SPJ

STOP

REV

NOTE

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды