mori seiki ZL-153 Скачать руководство пользователя страница 8

Страница: 8 / 561

-4- FOR SAFE OPERATION

SO-NL-B9E/O

DANGER

Cover power supply cables that are run along the floor with rigid

insulated plates to prevent them from being damaged.

Damage to the insulation of the power supply cable could cause

electric shocks.

Even after the power is turned off, some devices will remain charged

and the temperature of motors, lights inside the machine, etc., will

remain high. Make sure that the charge has been discharged or the

temperature has fallen before carrying out maintenance work or

inspections on these devices. If you touch these devices/units

carelessly while they are still charged or while the temperature is

still high you could receive an electric shock or be burned.

Check that all cables are properly insulated before using the

machine. There is considerable danger of electric shock if damaged

cables are used.

WARNING

Keep the floor area around the machine tidy and clean; do not leave

things lying on it, and clean up spilled water or oil immediately. If

you fail to do this, plant personnel may injure themselves by tripping

over or slipping on the floor.

Before operating the machine, check the area where you will have to

stand and walk to make sure you can operate the machine safely. If

you do not check your footing beforehand, you could loose your

balance while working and injure yourself by putting your hands in a

dangerous place while trying to find support, or by falling over.

Before using a switch, button, or key, check visually that it is the one

you intend to use, and then press or set it decisively.

Pressing the wrong switch, button, or key by mistake can cause

accidents involving serious injuries or damage to the machine.

Always keep the front door closed during machine operation.

Leaving the machine running or operating it with the front door open

could cause accidents involving serious injuries or damage to the

machine; plant personnel could be seriously injured by being

entangled in the rotating parts of the machine or crushed by its

moving parts, struck by a workpiece or soft jaws if they fly out of the

chuck, hit by flying chips, or splashed with coolant.

The parameters are set on shipment in accordance with the machine

specifications; do not change them without first consulting Mori

Seiki. If the parameters are changed without consultation, the

machine may operate in an unexpected manner, causing accidents

involving serious injuries or damage to the machine.

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды