mori seiki ZL-153 Скачать руководство пользователя страница 288

Страница: 288 / 561

B-60 MANUAL OPERATION

Press the TSUCLP switch.

The tailstock is unclamped and the joint pin extends

from the tailstock so that it is connected to the

saddle 1.

The indicator in the TSCLP switch goes off and the

indicator in the TSUCLP switch is lit.

Select any of the following modes with the MODE

selection switch.

(handle)

(jog)

(rapid traverse)

(zero return)

Once the tailstock is unclamped, the tailstock can

be moved by the saddle 1 in any of the above

modes.

10)

Move the tailstock to the required position by

moving the Z-axis with zero return, rapid traverse,

jog feed, or handle feed operation.

When moving the tailstock to the required

position, its motion direction for positioning should

be only in the negative direction.

If positioning is completed with motion in the

positive direction, it will not be possible to perform

a clamp operation subsequently.

11)

Press the TSCLP switch.

The tailstock is clamped; it is disconnected from the

saddle 1.

The indicator in the TSUCLP switch goes off and the

indicator in the TSCLP switch is lit.

TSCLP

TSTMOD

TSUCLP

MODE

MEM

MDI

TAPE

EDIT

JOG

RPD

ZRN

HANDLE

x10

x100

AXIS DIRECTION

NOTE

TSCLP

TSTMOD

TSUCLP

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды