mori seiki ZL-153 Скачать руководство пользователя страница 537

Страница: 537 / 561

PREPARATION BEFORE STARTING MASS PRODUCTION F-53

<Turret 1 is used for spindle 1 and turret 2 for spindle 2>

There are following four patterns for specifying the

synchronous operation.

The program and the spindle states are indicated below

for each of the four patterns.

An alarm (EX1429) occurs if the direction of

spindle rotation does not agree between spindle 1

and spindle 2 when spindle rotation is designated

by M03 or M04 for spindle 1 and M203 or M204

for spindle 2.

<Pattern 1>

Specify "M03 (M04) S

" in the program for turret 1.

Specify M34 (M35) in both of the programs.

Both spindles rotate in synchronization at the specified speed S

Specify "M36" in either of the programs.

Spindle 1 keeps rotating at S

while spindle 2 stops.

<Pattern 2>

Specify "M204 (M203) S

" in the program for turret 2.

Specify M34 (M35) in both of the programs.

Both spindles rotate in synchronization at the speed specified at turret 1.

Specify "M36" in either of the programs.

Spindle 1 stops while spindle 2 keeps rotating at S

<Pattern 3>

Specify "M03 (M04) S

" in the program for turret 1.

Specify M234 (M235) in both of the programs.

Both spindles rotate in synchronization at the speed specified at turret 2.

Specify "M36" in either of the programs.

Spindle 1 keeps rotating at S

while spindle 2 stops.

<Pattern 4>

Specify "M204 (M203) S

" in the program for turret 2.

Specify M234 (M235) in both of the programs.

Both spindles rotate in synchronization at the specified speed S

Specify "M36" in either of the programs.

Spindle 1 stops while spindle 2 keeps rotating at S

Turret 1

Spindle 1

Turret 2

Spindle 2

NOTE

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды