mori seiki ZL-153 Скачать руководство пользователя страница 81

Страница: 81 / 561

P-30 DOOR INTERLOCK FUNCTION

5-2-3

Emergency Stop and Door Unlock (Automatic Door Type)

When the machine enters the emergency stop state, the door is placed in the unlocked state.

When the emergency stop state is reset while the door is closed (not locked), the door is locked.

If the emergency stop state is reset while the door is open, the following message is

displayed.

"EX4002 OPEN THE DOOR THEN CLOSE"

In this case, the alarm is released when the door is closed and locked by pressing the

AUTOMATIC DOOR CLOSE switch.

5-3

Keeping the Door Unlocked

Since the machine is equipped with the door lock device, the door is automatically locked when it

is closed and if the door is locked it is not possible to open the door from the inside of the machine

(inside of the door). To keep the DOOR UNLOCKed when the door is closed with a person

working inside the door for setup, cleaning, inspection, or repair, a door lock prevention key is

provided.

Depending on the machine models, the door lock prevention key may not be provided.

Turn the key counterclockwise and the door is not locked.

When the door is closed with the door lock prevention key

turned counterclockwise, the door is not locked.

The specifications and the installation positions of the door lock device will vary according

to the machine model and specification.

WARNING

The door is automatically locked when it is closed and the locked door

cannot be opened from the inside of the machine (inside of the door). To

carry out maintenance or inspection work inside the machine, make the

lock device invalid by turning the door lock prevention key; remove the

key and bring it with you when you enter the machine. To prevent the

door being locked by mistake, lock a padlock in the hole at the end of the

door lock hasp. If the door is closed by mistake while the door lock device

is valid, the door is locked and you may be cooped up in the machine. If

the machine is started while you are inside the machine, you will be

entangled with the rotating part or crushed between sliding parts to be

seriously injured.

NOTE

Door lock prevention key

NOTE

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды