Mitsubishi SCM100ZJ-S1, Руководство по обслуживанию

Страница: 29 / 246

- -
'11 • SCM-SM-110
Stop
(1)
Indoor unit operation mode
Control A
Control B
Compressor ON
Compressor OFF
Cooling Dehumidifying Heating Fan (2)
Note (1) Including the stop from the cooling, dehumidifying, fan
and heating, and the anomalous stop
(2) Including the “Fan” operation according to the
mismatch of operation modes
1)
Control A
a) If the float switch detects any anomalous draining condition, the unit stops with the anomalous stop (displays E9)
and the drain pump starts. After detecting the anomalous condition, the drain motor continues to be ON.
b) It keeps operating while the float switch is detecting the anomalous condition.
2)
Control B
If the float switch detects any anomalous drain condition, the drain motor is turned ON for 5 minutes, and at 10
seconds after the drain motor OFF it checks the float switch. If it is normal, the unit is stopped under the normal
mode or, if there is any anomalous condition, E9 is displayed and the drain motor is turned ON. (The ON condition is
maintained during the drain detection.)
(n) Operation check/drain pump test run operation mode
1) If the power is turned on by the dip switch (SW7-1) on the indoor PCB when electric power source is supplied, it enters the
mode of operation check/drain pump test run. It is ineffective (prohibited) to change the switch after turning power on.
2) When the communication with the remote controller has been established within 60 seconds after turning power on by the
dip switch (SW7-1) ON, it enters the operation check mode. Unless the remote controller communication is established, it
enters the drain pump test run mode.
Note (1) To select the drain pump test run mode, disconnect the remote controller connector (CNB) on the indoor PCB to shut down the remote controller
communication.
3) Operation check mode
There is no communication with the outdoor unit but it allows performing operation in respective modes by operating the
remote controller.
4) Drain pump test run mode
As the drain pump test run is established, the drain pump only operates and during the operation protective functions by
the microcomputer of indoor unit become ineffective.
(o) Cooling, dehumidifying frost protection
1) To prevent frosting during cooling mode or dehumidifying mode operation, the of compressor speed is reduced if
the indoor heat exchanger temperature (detected with ThI-R) drops to 1.0 °C or lower at 4 minutes after the start of
compressor operation. If the indoor unit heat exchanger temperature is 1.0 °C or lower after 1 minutes, the compressor
speed is reduced further. If it becomes 2.5 °C or higher, the control terminates. When the indoor heat exchanger
temperature has become as show below after reducing the compressor speed, it is switched to the fan operation. For the
selection of indoor fan speed, refer to item 2).
10 1.0
Indoor heat exchanger temperature (°C)
Fan operation
Cooling operation
SRC40~60
FDC100~140
Model
Symbol
A
4
4
1
1
1.0
1.0
2.5
2.5
B C D
(m) Drain motor (DM) control [Applicable model: FDTC and FDUM]
( i )
Drain detection switch is turned ON or OFF with the float switch (FS) and the timer.
[
＊
] Drain detection switch is turned “ON” when the float switch “Open” is detected for seconds continuously in the
drain detectable space.
[
＊
] Drain detection switch is turned “OFF” when the float switch “Close” is detected for 0 seconds continuously.
1)
It detects always from 0 seconds after turning the power ON.
a) There is no detection of anomalous draining for 0 seconds after turning the drain pump OFF.
b) Turning the drain detection switch “ON” causes to turn ON the drain pump forcibly.
c) Turning the drain detection switch “OFF” releases the forced drain pump ON condition.
(ii) Indoor unit performs the control A or B depending on each operating condition.
Normal state
[*1] [*2]
Normal state
Drain detection switch ON